KidKraft CRANBROOK PLAY SYSTEM Скачать руководство пользователя страница 53

Страница: 53 / 76

Place (1868) Table Support flush to the angled edge of (0376)

Table Top, as shown in fig. 26.3. The overhang should measure

3-3/8” on each side. Attach using 5 (S7) #12 x 2” Pan Screws.

Place Table Top Assembly tight to the top of (1852) CE Siding,

(1808) Short Trim and (1870) Trim Short. Make sure (1868) Table

Support is flush to the outside edges of both (2383) Posts then attach

(1868) Table Support to each post with 2 (S3) #8 x 2-1/2” Wood

Screws per post. (fig. 26.4 and 26.5)

Hardware

Wood Parts

4 x

#8 x 2-1/2” Wood Screw

5 x

#12 x 2” Pan Screw

1 x

Table Top 5/4 x 6 x 32”

1 x

Table Support 2 x 2 x 38-3/4”

0376

1868

2383

Fig. 26.3

Flush

1868

0376

Fig. 26.5

1868

1852

1808

1870

Front Wall

Fig. 26.4

Step 26: Lower Cafe Wall Assembly

Part 2

Flush

3-3/8”

2383

x 4

Содержание CRANBROOK PLAY SYSTEM













































































Результаты поиска

Содержание CRANBROOK PLAY SYSTEM

Отзывы:

Бренды по названию

Популярные бренды

KidKraft CRANBROOK PLAY SYSTEM, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CRANBROOK PLAY SYSTEM

Отзывы:

Бренды по названию

Популярные бренды