background image

7

TROUBLESHOOTING

If your amplifi er does not appear to be working, check the obvious things fi rst such as blown fuses, poor or 
incorrect wiring connections, incorrect setting of crossover switch and gain controls, etc. There are Power (PWR) 
& Protection (PRT) LEDs on the side panel of your Kicker DXA series amplifi er. Depending on the state of the 
amplifi er and the vehicle’s charging system, the LEDs will glow either green or red. When the green LED is lit, this 
indicates the amplifi er is turned on and no trouble exists.

Green LED off, no output? 

With a Volt Ohm Meter (VOM) check the following:  

+12 volt power terminal 

(should read +12V to +16V)   

Remote turn-on terminal (should read +12V to +16V)   

Check for reversed 

power and ground connections   

Ground terminal, for proper conductivity.

Green LED on, no output? 

Check the following:   

RCA connections   

Test speaker outputs with a 

“known” good speaker.   

Substitute source unit with a “known” good source unit.   

Check for a signal in the 

RCA cable feeding the amplifi er with the VOM meter set to measure “AC” voltage.  

Red LED fl ashing with loud music?

 The red LED indicates low battery voltage. Check all the connections in 

your vehicle’s charging system. It may be necessary to replace or charge your vehicle’s battery or replace your 
vehicle’s alternator.

Red LED on, no output?

 

Amplifi er is very hot 

thermal protection is engaged. Test for proper impedance at 

the speaker terminals with a VOM meter (see the diagrams in this manual for minimum recommended impedance 
and multiple speaker wiring suggestions). Also check for adequate airfl ow around the amplifi er.  

Amplifi er 

shuts down only while vehicle is running = voltage protection circuitry is engaged. Voltage to the amplifi er is not 
within the 10–16 volt operating range. Have the vehicle’s charging and electrical system inspected.  

Amplifi er 

will only play at low volume levels = short circuit protection is engaged. Check for speaker wires shorted to 
each other or to the vehicle chassis. Check for damaged speakers or speaker(s) operating below the minimum 
recommended impedance.

No or low output?

 

Check the balance control on source unit  

Check the RCA (or speaker input) and 

speaker output connections.
 

Alternator noise-whining sound with engine’s RPM?

 

Check for damaged RCA (or speaker input) cable  

Check the routing of RCA (or speaker input) cable  

Check the source unit for proper grounding  

Check 

the gain settings and turn them down if they are set too high.

Reduced bass response?

 Reverse a speaker connection from positive to negative on the stereo/subwoofer 

channel(s); if the bass improves, the speaker was out of phase.

Ground Noise?

  KICKER amplifi ers are engineered to be fully compatible with all manufacturers’ head units. 

Some head units may require additional grounding to prevent noise from entering the audio signal. If you are 
experiencing this problem with your head unit, in most cases running a ground wire from the RCA outputs on the 
head unit to the chassis will remedy this issue.

CAUTION:

  When jump starting the vehicle, be sure that connections made with jumper cables are correct. 

Improper connections can result in blown amplifi er fuses as well as the failure of other critical systems in the 
vehicle.

If you have more questions about the installation or operation of your new KICKER product, see the Authorized 
KICKER Dealer where you made your purchase. For more advice on installation, click on the SUPPORT tab on 
the KICKER homepage, 

www.kicker.com

. Choose the TECHNICAL SUPPORT tab, choose the subject you are 

interested in, and then download or view the corresponding information. Please E-mail [email protected] or 
call Technical Services (405) 624-8583 for unanswered or specifi c questions.

2014 DXA 4-Channel Amps Rev A.indd   7

2014 DXA 4-Channel Amps Rev A.indd   7

8/2/2013   4:44:14 PM

8/2/2013   4:44:14 PM

Содержание DXA250.4

































Отзывы: