background image

6

Fig. 11

7. ELECTRICAL CONNECTIONS

6. INSTALLATION OF SAFETY SUPPORT

   

(for Canadian Installation ONLY)

A safety support cable is provided to help 
prevent the ceiling fan from falling, please 
install it as follows.

Step 1. Attach the provided wood screw and 
washers to the ceiling joist next to the 
mounting bracket but do not tighten. (Fig. 11)

Step 2. Adjust the length of the safety cable to 
reach the screw and washers by pulling the 
extra cable through the cable clamp until the 
overall length is correct, put the end of the 
cable back through the cable clamp, forming a 
loop at the end of the cable. Tighten the cable 
clamp securely. Now, put the loop in the end of
the safety cable over the wood screw and 
under the washer. Tighten the wood screw 
securely.

Ceiling mounting 
bracket

Attach
safety cable
to ceiling joist
with screw and
washer  

Fig. 12

WARNING:

 To avoid possible electrical shock, 

be sure you have turned off the power at the 
main circuit panel.

Follow the steps below to connect the fan to 
your household wiring. Use the wire 
connecting nuts suppled with your fan. Secure 
the connectors with electrical tape. Make sure 
there are no loose wire strands or 
connections.

Step 1.

 Connect the fan supply (black) wire 

and light supply (blue) wire to the black 
household supply wire as shown in Figure 12.

Step 2.

 Connect the neutral fan (white) wire to 

the neutral household (white) wire.

Step 3.

 Connect the fan ground wire (green) to 

the household ground wire.

Step 4.

 After connecting the wires, spread 

them apart so that the green and white wires 
are on one side of the outlet box and the black 
and the blue wires are on the other side.

Step 5.

 Turn the connecting nuts upward and 

push the wiring into the outlet box. 

WARNING:

 TO REDUCE THE RISK OF 

FIRE, ELECTRIC SHOCK OR OTHER 
PERSONAL INJURY, MOUNT YOUR 
CEILING FAN ON A OUTLET BOX OR 
SUPPORTING SYSTEM MARKED 
"ACCEPTABLE FOR FAN SUPPORT".

BLUE 

BLK

BLK

GRN

Wiring

box

Ground to

mounting

bracket

or downrod

BLUE

BLUE

FAN

LIGHT

Power lines 220~240V

Green ground

RED

RED

BLK

BLK

Bronson

TM

Содержание Bronson













Отзывы: