WARNING – RISK OF ELECTRIC SHOCK
1) Use only in ponds and small decorative fountains where persons will
immerse no more than their hands and lower arms while the product is
energized.
2)
DO NOT
use in water intended for swimming, wading, immersion, or
bathing.
3) All installer completed cable connections must be located outside of
pond or fountain.
4) Low voltage circuit must be supplied by a power unit marked as suitable
for supplying submersible luminaires.
5) Power unit must be supplied by a branch circuit protected by a Class A
type ground fault circuit interrupter (GFCI).
6) Maximum Depth: 72” (1.8m).
7) Wiring connections must be made with approved/listed wire connection
device(s) suitable for the application. Do not exceed manufacturers’
wiring combination specifications for size and quantity of conductors.
8) This fixture is to be used only with a listed power unit (transformer) rated a
maximum of 300 W (25 AMPS) 15 volts.
9)
The unit low voltage cable integral to the product is intended for
shallow burial - maximum 6 inches (152 mm).
10) Low voltage cable shall be protected by routing in close proximity to the
luminaire, or next to a building structure such as a house or deck and not
be buried except for a maxiumum of 6 inches (15.2 cm).
11) Direct burial rated wire is to be buried a minimum of 6” (152mm) beneath
the surface of the ground.
12)
NOTE:
If additional Direct Burial wire is needed, contact your local
Kichler
®
landscape distributor.
• 8 GA wire can be purchased in length of 250’ (76 M), 15503-BK.
• 10 GA wire can be purchased in length of 250’ (76 M), 15504-BK.
• 12 GA wire can be purchased in lengths of 100’ (30 M), 15501-BK; 250’
(76 M), 15502-BK; 500’ (152M), 15505-BK; and 1000’ (304 M),
15506-BK.
SAFETY INSTRUCTIONS
READ THIS FIRST
KEEP THESE INSTRUCTIONS
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main fusebox
before installation.
This fixture is intended for installation in accordance with the National
Electric Code (NEC) and Local code specifications. Failure to adhere to
these codes and instructions may result in serious injury and/or property
damage and will void the warranty. If you are not familiar with code
requirements, installation by a certified electrician is recommended.
CAUTION
WHEN INSTALLING KICHLER LANDSCAPE LIGHTING (LINE VOLTAGE
OR LOW VOLTAGE), CARE SHOULD BE TAKEN TO KEEP CLEAR OF
POTENTIALLY COMBUSTIBLE MATERIALS.
WHEN MAINTAINING THE FIXTURES, BE SURE TO REMOVE LEAVES,
PINE NEEDLES, GRASS CLIPPINGS, MULCH, OR ANY DEBRIS THAT
HAS ACCUMULATED ON THE LIGHT BULB, LENS, OR BODY OF THE
FIXTURE.
For warranty information please visit:
kichler.com/customer-care/warranty-information/landscape-warranty
Installation for Use as Underwater Fixture:
1) Turn off power.
2) Make wire connections directly to a low voltage transformer or connect to
low voltage power supply cable using approved/listed wire connection
device(s) suitable for the application.
NOTE:
Connection from the fixture cable to power supply cable must
not be submerged.
3) Fixture can be placed in water by itself to be hidden or tucked away into
rocks. To adjust the tilt angle of fixture, loosen the thumb screws,
adjust the fixture to the desired angle, and re-secure by tightening the
thumbscrews. Fixture can be used without cowl and/or bracket. To
remove the cowl and/or bracket, loosen and remove the thumbscrews,
slide the bracket off from the side, and slide the cowl and rubber washers
off from the top. When using fixture without bracket, tuck fixture into
rocks and backfill rocks around the fixture to secure in desired location.
4) Place fixture in desired location.
NOTE:
Always keep minimum 3” clearance from face/lens of product.
5) To weight down bracket for in-water use, stones or pebbles can be used
at base of bracket. Bracket can also be fastened to a larger flat stone
using optional size 3/16” stainless steel masonry screws (not supplied).
6) When using fixture in bodies of water that freeze, pull fixture out of water
before water freezes. Do not place fixture back into water until
after water thaws.
Installation for Out of Water Use:
1) Turn off power.
2) The base of the bracket may be used as a template for marking the
desired mounting screw locations. At the desired location, drive one of
the mounting screws (provided) part way into the mounting surface. Slip
the base of the bracket over the screw by passing the mounting screw
head through center opening. Tighten the mounting screw to hold the
bracket in position. Drive the second mounting screw completely to fully
secure the bracket.
NOTE:
Always keep minimum 3” clearance from face/lens of product.
3) If you wish to conceal the wire to the fixture, drill a wire opening in the
mounting surface through the center of the opening in the base of the
bracket.
4) To adjust the tilt angle of fixture, loosen the thumbscrews, adjust the
fixture to the desired angle, and re-secure by tightening the
thumbscrews. Fixture can be used without cowl and/or bracket. To
remove the cowl and/or bracket, loosen and remove the thumbscrews,
slide the bracket off from the side, and slide the cowl and rubber washers
off from the top. When using fixture without bracket, tuck fixture into
rocks and backfill rocks around the fixture to secure in desired location.
5) Make wire connections directly to a low voltage transformer or connect to
low voltage power supply cable using approved/listed wire connection
device(s) suitable for the application.
NOTE:
Connection from the fixture cable to power supply cable must not
be submerged.
To change light output setting:
NOTE:
To adjust lumen output for this fixture, see “To change light
output setting” instructions on Page 2.
IS-16027SS-US
We’re here to help
866-558-5706
Hrs: M-F 9am to 5pm EST
FIXTURE
COWL
THUMBSCREW
RUBBER WASHER
BRACKET
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1)
This device may not cause harmful interference, and
2)
This device must accept any interference received, including interference that may cause undesired
operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
FCC INFORMATION
Page 1
CONFORMS TO ANSI/UL STD. 1838 CERTIFIED TO CSA STD. C22.2 NO. 250.7
