7
OPERATING INSTRUCTIONS
Operating Instructions
-
Press the "MODE" button until the "COOL"
indicator light comes on.
-
Press the ADJUST buttons "+" or " - " to
select your desired room temperature. The
temperature can be set within a range of
17 C-30 C/62 F-88 F (or 86 F).
-
Press the "FAN SPEED" button to choose the
fan speed.
O
O
O
O
O
-
Press the "MODE" button until the "DRY"
indicator light comes on.
-
Under this mode, you cannot select a fan
speed or adjust the temperature. The fan
motor operates at LOW speed.
-
Keep windows and doors closed for the
best dehumidifying effect.
-
Do not put the duct to window.
COOL operation
-
Press the "MODE" button until the
"FAN " indicator light comes on.
-
Press the "FAN SPEED" button to
choose the fan speed. The temperature
cannot be adjusted.
-
Do not put the duct to window.
FAN operation
TIMER operation
-
Press the "MODE" button until the "HEAT"
indicator light comes on.
-
Press the ADJUST buttons "+" or " - " to
select your desired room temperature. The
temperature can be set within a range of
17 C-30 C/62 F-88 F (or 86 F).
-
Press the "FAN SPEED" button to choose the
fan speed. For some models, the fan speed
can not be adjusted under HEAT mode.
O
O
O
O
O
HEAT operation
(cooling only models without)
AUTO operation
-
When you set the air conditioner in AUTO
mode, it will automatically select cooling,
heating(cooling only models without), or
fan only operation depending on what
temperature you have selected and the
room temperature.
-
The air conditioner will control room
temperature automatically round the
temperature point set by you.
-
Under AUTO mode, you can not
select the fan speed.
FOLLOW ME/TEMP SENSING feature(optional)
To activate the Follow Me/Temp Sensing
feature, point the remote control towards
the unit and pres s the Follow Me/Temp
Sensing button. T
If the unit does not receive
the Follow Me/Temp Sensing signal during
any 7 minutes interval, the unit will beep to
indicate the Follow Me/Temp Sens ing mode
has ended.
he remote display is
actual temperature at its location. The
remote control will send this signal to the
air conditioner every 3 minutes interval
until press the Follow Me/Temp Sensing
button again.
NOTE:This feature can be activated from the
rem ote con tro l ON LY. The rem ote con trol
servesas a rem ote thermostat allowing for the
precise tem perature control at its location.
-
When the unit is on, press the
Timer button will initiate the Auto-off
stop program, the TIMER OFF
indicator light illuminates. Press the
UP or down button to select the desired
time. Press the TIMER button again
within 5 seconds, the Auto-on start
program is initiated. And the TIMER
ON indicator light illuminates. Press
the up or down button to select the
desired Auto-on start time.
-
- Press or hold the UP or D OWN
button to change the Auto time by
0.5 hour increments, up to 10 hours,
then at 1 hour increments up to 24
hours. The control will count down
the time remaining until start.
-
The system will automatically revert
back to display the previous temper-
ature setting if there is no operation
in a five seconds period.
When the unit is off, press the Timer
button to initiate the Auto-on start
program,press it again within five
seconds will initiate the Auto-off stop
program.
Error codes and protection code:
E1-
E2-
E3-
E4-
P1-
Room temper ature sensor error-
Unplug the unit and plug it back in.
If error r epeats, call for service.
Evaporator temperature sensor error-
Unplug the unit and plug it back in.
If error r epeats, call for service.
Condenser temperature sensor error-
Unplug the unit and plug it back in. If error
repeats , call for serv ice (on some models).
error-
Unplug the unit and plug it back in.
If error r epeats, call for service.
Bottom tray is full - Connect the
drain hose and drain the collected
water away. If protection repeats, call
for service.
Display panel communication