Keysight E6650A EXF Скачать руководство пользователя страница 216 | Manualshive

Страница: 216 / 657

background image

6 List Sequence Measurements
Marker

Marker

The Marker key accesses the Marker menu. A marker can be placed on a trace to allow the value of the
trace at the marker point to be determined precisely. The functions in this menu include a 1-of-N selection
of the control mode Normal, Delta, or Off for the selected marker.

Markers may also be used in pairs to read the difference (or delta) between two data points. They can be
used in Marker Functions to do advanced data processing, or to specify operating points in functions like
Signal Track and N dB Points.

parameter_table_23.52941

52.94118

Key Path

Front-Panel

Initial S/W Revision

A.05.00

Help Map ID

35265

Marker Select

Specifies the selected marker. The term “selected marker” is used specify which marker is affected by the
functions.

parameter_
table_
23.52941

52.94118

Key Path

Marker

Notes

The selected marker is remembered even when not in the Marker menu and is used if a Search is done or a
Band Function is turned on or for Signal Track or Continuous Peak.

Preset

Marker 1

State Saved

The number of the selected marker is saved in instrument state.

Initial S/W
Revision

A.05.00

Help Map ID

35246

Marker Control Mode

There are three control modes for markers:

Normal (POSition) - A marker that can be moved to any point on the X Axis by specifying its X Axis value; its
absolute Y Axis valueis then the value of the trace point at that X Axis value.

D Delta (DELTa) - A marker that can be moved to any point on the X Axis by specifying its X Axis offset from
a reference marker; its absolute Y Axis value is then the value of the trace point at that X Axis value.

Off (OFF) - A marker which is not in use.

216

Sequence Analyzer User's & Programmer's Reference

«
...
214
215
216
217
218
...
»

Содержание E6650A EXF


















































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для E6650A EXF

Бренд: Fein Страницы: 248

Бренд: ZF Страницы: 30

Бренд: Raymarine Страницы: 111

Tetrix 351 AC/DC Smart FW

Бренд: EWM Страницы: 117

Бренд: Jacobs Ladder Страницы: 16

Бренд: Bahco Страницы: 9

Бренд: Kawai Страницы: 10

Бренд: Idmed Страницы: 2

Бренд: Kamikaze Страницы: 112

Бренд: KAM Страницы: 2

Бренд: KaVo Страницы: 4

ORTHOPANTOMOGRAPH OP 3D

Бренд: KaVo Страницы: 40

KEY Laser III 1243

Бренд: KaVo Страницы: 103

EXTRAmatic 9040

Бренд: KaVo Страницы: 56

ESTETICA E70 Vision

Бренд: KaVo Страницы: 48

Бренд: Kaya Safety Страницы: 5

Бренд: XTA Страницы: 20

Бренд: Kawai Страницы: 166

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды