Keysight E3630A Скачать руководство пользователя

Страница: 29 / 71

Installation

Keysight E3630A Operating and Service Manual

Installation Data

The instrument is shipped ready for bench operation. Before applying power to

the supply, please read the

Input Power Requirements

paragraph.

Location and cooling

This instrument is air cooled. Sufficient space should be allowed so that a free

flow of cooling air can reach the sides and rear of the instrument when it is in

operation. It should be used in an area where the ambient temperature does not

exceed 40 °C.

Outline diagram

Figure 2-1

illustrates the outline shape and dimensions of the supply.

Rack mounting

This supply may be rack mounted in a standard 19-inch rack panel either by itself

or alongside a similar unit. Please see the

“Accessory”

on page 21

for available

rack mounting accessory. The rack-mounting kit includes complete installation

instructions.

Input Power Requirements

Depending on the line voltage option ordered, the supply is ready to be operated

from one of the power sources listed in

Table 1-1

. A label on the rear heat sink

shows the nominal input voltage set for the supply at the factory.

Power cable

To protect operating personnel, the supply should be grounded. This supply is

equipped with a three conductor power cable. The third conductor is the ground

conductor and when the cable is plugged into an appropriate receptacle, the

supply is grounded.

Содержание E3630A








































































Результаты поиска

Содержание E3630A

Отзывы:

Похожие инструкции для E3630A

Бренды по названию

Популярные бренды

Keysight E3630A, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание E3630A

Отзывы:

Похожие инструкции для E3630A

Бренды по названию

Популярные бренды