Keysight E3630A Скачать руководство пользователя

Страница: 58 / 71

Service Information

Keysight E3630A Operating and Service Manual

Stability (Drift)

Definition:

The change in output voltage (DC to 20 Hz) for the first 8 hours

following a 30-minute warm-up period with constant input line voltage, constant

load resistance and constant ambient temperature.
To measure the stability:

Connect the test equipment across the output of the +20 V supply as shown in

Figure 5-5

Operate the electronic load in constant current mode and set its current to the

full rated value of power supply.

Turn on the supply.

Turn up output voltage to the full rated value as read on the digital voltmeter.

After a 30-minute warm-up, note the voltage on DVM.

The output voltage reading should deviate less than 0.1% plus 5 mV from the

reading obtained in step e over a period of 8 hours.

Repeat for the remaining supply outputs.

Содержание E3630A








































































Результаты поиска

Содержание E3630A

Отзывы:

Похожие инструкции для E3630A

Бренды по названию

Популярные бренды

Keysight E3630A, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание E3630A

Отзывы:

Похожие инструкции для E3630A

Бренды по названию

Популярные бренды