Keysight E3630A Скачать руководство пользователя

Страница: 44 / 71

Service Information

Keysight E3630A Operating and Service Manual

Maintenance

Introduction

This section provides performance test, troubleshooting information, and

adjustment and calibration procedures. The following operation verification tests

comprise a short procedure to verify that the power supply is performing properly,

without testing all specified parameters.
If a fault is detected in the power supply while making the performance check or

during normal operation, proceed to the troubleshooting procedures. After

troubleshooting, perform any necessary adjustments and calibrations. Before

returning the power supply to normal operation, repeat the performance check to

ensure that the fault has been properly corrected and that no other faults exist.

Test equipment required

The following

Table 5-1

lists the equipment required to perform the various

procedures described in this section.

Table 5-1

Test equipment required

Type

Required characteristics

Use

Recommended model

Oscilloscope

Sensitivity : 100

Bandwidth : 20 MHz/100 MHz

Display transient response and

ripple and noise waveforms.

Keysight 54600A

RMS voltmeter

True rms, 20 MHz bandwidth
Sensitivity : 1 mV
Accuracy : 5%

Measure rms ripple and noise
voltage.

Multimeter

Resolution : 100 nV
Accuracy : 0.0035%

Measure DC voltages.

Keysight 34401A

Electronic load

Voltage range : 240 VDC
Current range : 10 ADC
Open and short switches
Transient on/off

Measure load and line

regulation.

Keysight 6063A

Resistive loads (R

)

Ω

20 W, 2.4

Ω

20 W

Measure ripple and noise.

Содержание E3630A








































































Результаты поиска

Содержание E3630A

Отзывы:

Похожие инструкции для E3630A

Бренды по названию

Популярные бренды

Keysight E3630A, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание E3630A

Отзывы:

Похожие инструкции для E3630A

Бренды по названию

Популярные бренды