Keysight DSOX3012T Скачать руководство пользователя страница 63

Страница: 63 / 530

Keysight InfiniiVision 3000T X-Series Oscilloscopes

User's Guide

2 Horizontal Controls

To adjust the horizontal (time/div) scale / 64
To adjust the horizontal delay (position) / 65
Panning and Zooming Single or Stopped Acquisitions / 66
To change the horizontal time mode (Normal, XY, or Roll) / 67
To display the zoomed time base / 71
To change the horizontal scale knob's coarse/fine adjustment setting / 72
To position the time reference (left, center, right, custom) / 72
Searching for Events / 73
Navigating the Time Base / 75

The horizontal controls include:
• The horizontal scale and position knobs.
• The

[Horiz]

key for accessing the Horizontal Menu.

• The

zoom key for quickly enabling/disabling the split-screen zoom display.

• The

[Search]

key for finding events on analog channels or in serial decode.

• The

[Navigate]

keys for navigating time, search events, or segmented memory

acquisitions.

• Touchscreen controls for setting the horizontal scale and position (delay),

accessing the Horizontal Menu, and navigating.

The following figure shows the Horizontal Menu which appears after pressing the

[Horiz]

key.

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды