manualshive.com logo in svg

Keysight DSOX3012T, Руководство пользователя

Keysight DSOX3012T - мощный осциллограф с функциональностью отличного качества. Пользовательская инструкция доступна для бесплатного скачивания на manualshive.com. Используйте этот ресурс для получения подробной информации о продукте и его функциях. Идеальный инструмент для профессиональных и любительских проектов.

Поделиться
Скачать
background image

Horizontal Controls

2

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

73

 

2

In the Horizontal Menu, press 

Time Ref

; then, select:

•

Left

 — the time reference is set to one major division from the left edge of the 

display.

•

Center

 — the time reference is set to the center of the display.

•

Right

 — the time reference is set to one major division from the right edge of 

the display.

•

Custom Location

 — lets you place the time reference location at a percent of 

the graticule width (where 0% is the left edge and 100% is the right edge).

A small hollow triangle (

∇

) at the top of the display grid marks the position of the 

time reference. When delay time is set to zero, the trigger point indicator (

▼

) 

overlays the time reference indicator.

The time reference position sets the initial position of the trigger event within 

acquisition memory and on the display, with delay set to 0.

Turning the Horizontal scale (sweep speed) knob expands or contracts the 

waveform about the time reference point (

∇

). See 

“To adjust the horizontal 

(time/div) scale"

on page 64.

Turning the Horizontal position (

) knob in Normal mode (not Zoom) moves the 

trigger point indicator (

▼

) to the left or right of the time reference point (

∇

). See 

“To adjust the horizontal delay (position)"

on page 65.

Searching for Events

You can use the 

[Search]

 key and menu to search for Edge, Pulse Width, Rise/Fall 

Time, Runt, Frequency Peaks, and Serial events on the analog channels.

Setting up searches (see 

“To set up searches"

on page 74) is similar to setting up 

triggers. In fact, except for Frequency Peaks and Serial events, you can copy 

search setups to trigger setups and vice-versa (see 

“To copy search setups"

on 

page 74).

Searches are different than triggers in that they use the measurement threshold 

settings instead of trigger levels.

Found search events are marked with white triangles at the top of the graticule, 

and the number of events found is displayed in the menu line just above the 

softkey labels.

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DSOX3012T

T-Drill F-400 Instruction Manual preview
F-400
Бренд: T-Drill Страницы: 75
Zeiss KS Instructions For Use Manual preview
KS
Бренд: Zeiss Страницы: 38
GBC AIO Quick Start Manual preview
AIO
Бренд: GBC Страницы: 8
KAPSCH T600 Operator And Maintenance Manual preview
T600
Бренд: KAPSCH Страницы: 57
GE MicroVersaTrip Plus Installation Instructions Manual preview
MicroVersaTrip Plus
Бренд: GE Страницы: 20
GE b30 Technical Reference Manual preview
b30
Бренд: GE Страницы: 252
Balanced Body Duet Manual preview
Duet
Бренд: Balanced Body Страницы: 12
Eagle Pro EL Series Instruction Sheet preview
EL Series
Бренд: Eagle Pro Страницы: 6
GE EntelliGuard G Instructions Manual preview
EntelliGuard G
Бренд: GE Страницы: 10
ADVANCED HOME CARE Helios Manual preview
Helios
Бренд: ADVANCED HOME CARE Страницы: 16
Abicor Binzel FES-200 W3 Short Instruction preview
FES-200 W3
Бренд: Abicor Binzel Страницы: 92
Hakko Electronics 192 Instruction Manual preview
192
Бренд: Hakko Electronics Страницы: 8
Hailo Professional HS 8 Assembly And Operation preview
Professional HS 8
Бренд: Hailo Страницы: 5
Hainbuch TESTit Installation Manual preview
TESTit
Бренд: Hainbuch Страницы: 52
M-system Mini-MW Series Manual preview
Mini-MW Series
Бренд: M-system Страницы: 5
MA dot2 User Manual preview
dot2
Бренд: MA Страницы: 2
MacDon FlexDraper FD2 Series Quick Start Manual preview
FlexDraper FD2 Series
Бренд: MacDon Страницы: 2
M-Audio OXYGEN PRO MINI Quick Start Manual preview
OXYGEN PRO MINI
Бренд: M-Audio Страницы: 56

Бренды по названию

Популярные бренды

Загрузить еще бренды