Keysight DSOX3012T Скачать руководство пользователя страница 71

Страница: 71 / 530

Horizontal Controls

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

To display the zoomed time base

Zoom, formerly called Delayed sweep mode, is a horizontally expanded version of

the normal display. When Zoom is selected, the display divides in half. The top

half of the display shows the normal time/div window and the bottom half

displays a faster Zoom time/div window.

The Zoom window is a magnified portion of the normal time/div window. You can

use Zoom to locate and horizontally expand part of the normal window for a more

detailed (higher-resolution) analysis of signals.

To turn on (or off) Zoom:

Press the

zoom key (or press the

[Horiz]

key and then the

Zoom

softkey).

The area of the normal display that is expanded is outlined with a box and the rest

of the normal display is ghosted. The box shows the portion of the normal sweep

that is expanded in the lower half.

These markers show the
beginning and end of the
Zoom window

Normal
window

Time/div
for zoomed
window

Time/div
for normal
window

Delay time
momentarily displays
when the Horizontal
position knob is turned

Zoom
window

Signal
anomaly
expanded
in zoom
window

Select
Zoom

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды