Keysight DSOX3012T Скачать руководство пользователя страница 352

Страница: 352 / 530

352

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Utility Settings

Press

File Name

to open the Remote Log Filename Menu where you can specify

the name of the file (on the USB storage device) to which remote commands

are logged.

Press

Display On

to enable or disable the screen display of logged remote

commands and their return values (if applicable).

Press

Transparent

to disable or enable a transparent background for the remote

command logging screen display.

Enable to make the background transparent. This lets you view underlying

waveforms.

Disable for a solid background which makes the logged remote commands

easier to read.

Performing Service Tasks

The Service Menu (under

[Utility] > Service

) lets you perform service-related tasks:

•

“To perform user calibration"

on page 352

•

“To perform hardware self test"

on page 355

•

“To perform front panel self test"

on page 356

•

“To display oscilloscope information"

on page 356

•

“To display the user calibration status"

on page 356

For other information related to oscilloscope maintenance and service, see:
•

“To clean the oscilloscope"

on page 356

•

“To check warranty and extended services status"

on page 356

•

“To contact Keysight"

on page 357

•

“To return the instrument"

on page 357

To perform user calibration

Perform user-calibration:

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды