Keysight DSOX3012T Скачать руководство пользователя страница 356

Страница: 356 / 530

356

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Utility Settings

To perform front panel self test

Pressing

[Utility] > Service > Front Panel Self Test

lets you test the front panel keys

and knobs as well as the oscilloscope display.

Follow the on-screen instructions.

To display oscilloscope information

Press

[Help] > About Oscilloscope

to display information about your oscilloscope:

• Model number.
• Serial number.
• Bandwidth.
• Module installed.
• Software version.
• Installed licenses. See also

“Loading Licenses and Displaying License

Information"

on page 378.

To display the user calibration status

Pressing

[Utility] > Service > User Calibration Status

displays the summary results of

the previous User Calibration, and the status of probe calibrations for probes that

can be calibrated. Note that passive probes do not need to be calibrated, but

InfiniiMax probes can be calibrated. For more information about calibrating probes

see

“To calibrate a probe"

on page 86.

To clean the oscilloscope

Remove power from the instrument.

Clean the external surfaces of the oscilloscope with a soft cloth dampened with

a mixture of mild detergent and water.

Make sure that the instrument is completely dry before reconnecting it to a

power source.

To check warranty and extended services status

To learn the warranty status of your oscilloscope:

Point your web browser to:

www.keysight.com/find/warrantystatus

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды