Keysight DSOX3012T Скачать руководство пользователя страница 378

Страница: 378 / 530

378

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Reference

Probes and Accessories

For a list of the probes and accessories that are compatible with the

3000T X-Series oscilloscopes, see the data sheet at:

www.keysight.com/find/3000TX-Series

AutoProbe

Interface

Most Keysight single-ended active, differential, and current probes are compatible

with the AutoProbe interface. Active probes that do not have their own external

power supply require substantial power from the AutoProbe interface.

If too much current is drawn from the AutoProbe interface, an error message will

be displayed, indicating that you must momentarily disconnect all probes to reset

the AutoProbe interface, then connect only the supported quantity of active

probes.

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды