Keysight DSOX3012T Скачать руководство пользователя страница 215

Страница: 215 / 530

215

Keysight InfiniiVision 3000T X-Series Oscilloscopes

User's Guide

13 Acquisition Control

Running, Stopping, and Making Single Acquisitions (Run Control) / 215
Overview of Sampling / 217
Selecting the Acquisition Mode / 221
Realtime Sampling Option / 227
Acquiring to Segmented Memory / 229

This chapter shows how to use the oscilloscope's acquisition and run controls.

Running, Stopping, and Making Single Acquisitions (Run Control)

There are two front panel keys for starting and stopping the oscilloscope's

acquisition system:

[Run/Stop]

and

[Single]

• When the

[Run/Stop]

key is green, the oscilloscope is running, that is, acquiring

data when trigger conditions are met.

To stop acquiring data, press

[Run/Stop]

. When stopped, the last acquired

waveform is displayed.

• When the

[Run/Stop]

key is red, data acquisition is stopped.

"Stop" is displayed next to the trigger type in the status line at the top of the

display.

To start acquiring data, press

[Run/Stop]

• To capture and display a single acquisition (whether the oscilloscope is running

or stopped), press

[Single]

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды