Keysight DSOX3012T Скачать руководство пользователя страница 166

Страница: 166 / 530

166

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Labels

To add an annotation

You can add up to four annotations to the oscilloscope's display. Annotations are

useful for documentation purposes, to add notes before capturing screens.

To add an annotation:

Press

[Display]

Label

In the label menu, press

Annotation

In the Annotation Menu, press the

Display

softkey and turn the Entry knob to

select the desired annotation.

Then, press the

Display

softkey again to enable/disable the annotation display.

When enabled, you can drag the annotation anywhere in the graticule using the

touchscreen, a USB mouse, or the

and

softkeys.

Press

Edit

In the Edit keypad dialog, you can enter text using:

•

The touch screen (when the front panel

[Touch]

key is lit).

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды