Keysight DSOX3012T Скачать руководство пользователя страница 147

Страница: 147 / 530

Digital Channels

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

147

In addition to the common mode voltage, longer ground returns also degrade the

pulse fidelity of the probe system. Rise time is increased, and ringing, due to the

undamped LC circuit at the input of the probe, is also increased. Because the

digital channels display reconstructed waveforms, they do not show ringing and

perturbations. You will not find ground problems through examination of the

waveform display. In fact, it is likely you will discover the problem through random

glitches or inconsistent data measurements. Use the analog channels to view

ringing and perturbations.

Best Probing Practices

Because of the variables L, di, and dt, you may be unsure how much margin is

available in your measurement setup. The following are guidelines for good

probing practices:
• The ground lead from each digital channel group (D15–D8 and D7–D0) should

be attached to the ground of the device under test if any channel within the

group is being used for data capture.

• When capturing data in a noisy environment, every third digital channel probe's

ground should be used in addition to the channel group's ground.

• High-speed timing measurements (rise time < 3 ns) should make use of each

digital channel probe's own ground.

When designing a high-speed digital system, you should consider designing

dedicated test ports that interface directly to the instrument's probe system. This

will ease measurement setup and ensure a repeatable method for obtaining test

data. The 01650-61607 16-channel logic probe cable and the 01650-63203

termination adapter are designed to make it easy to connect to industry-standard,

20-pin board connectors. The cable is a 2 m logic analyzer probe cable, and the

termination adapter provides the proper RC networks in a very convenient

package. These parts, as well as the 1251-8106 20-pin, low-profile, straight board

connector, can be ordered from Keysight Technologies.

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды