Keysight Technologies U3022AH10 Скачать руководство пользователя страница 88

Страница: 88 / 92

Instrument Markings

Listed below are definitions for the markings that may be found on the product.

IP 2 0

The instruction documentation symbol. The product is marked with this symbol when it is

necessary for the user to refer to the instructions in the documentation.

The AC symbol indicates the required nature of the line module input power.

This

symbol

indicates

separate

collection

for

electrical

and

electronic

equipment, mandated

under

EU law. All electric and electronic equipment are required to be separated from

normal waste for disposal (Reference WEEE Directive).

This symbol indicates that the power line switch is ON.

This symbol indicates that the power line switch is in the STANDBY position.

This symbol indicates that the power line switch is in the OFF position.

This symbol is used to identify a terminal which is internally connected to the product frame or

chassis.

The CE mark is a registered trademark of the European Community.

The

Keysight email address is

required by EU directives applicable to our product

The CSA mark is a registered trademark of the CSA International.

This

is a symbol of

an Industrial Scientific and Medical Group 1 Class A product (CISPR 11,

Clause 5)

This is a marking to indicate product compliance with the Canadian Interference-Causing
Equipment Standard (ICES-001).

Direct Current.

The instrument has been designed to meet the requirements of IP 2 0 for egress and

operational environment.

The RCM mark is a registered trademark of the Australian Communications and Media

Authority

Indicates the time period during which no hazardous or toxic substance elements are

expected to leak or deteriorate during normal use. Forty years is the expected useful life of

the product.

This symbol on all primary and secondary packaging indicates compliance to China standard

GB 18455-2001.

South Korean Certification (KC) mark; includes the marking's identifier code which follows the

format: MSIP-REM-YYY-ZZZZZZZZZZZZZZ.

ICES/NMB-001

[email protected]

U3022AH10

Safety and Regulatory Information

U3022AH10 User's and Service Guide

Содержание U3022AH10





























































































Результаты поиска

Содержание U3022AH10

Отзывы:

Похожие инструкции для U3022AH10

Бренды по названию

Популярные бренды

Keysight Technologies U3022AH10, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание U3022AH10

Отзывы:

Похожие инструкции для U3022AH10

Бренды по названию

Популярные бренды