Keysight Technologies U3020AD01 Скачать руководство пользователя страница 12

Страница: 12 / 42

U3020AD01

Front and Rear Panel Features

Table 5

LED Definitions and Instrument States

LED

Color

Instrument State

ATTN

LAN

PWR

Off

Green

Instrument in “ready” state

LAN connection established

- Instrument has an IP address

Firmware download complete

ATTN

LAN

PWR

Flashing

Green

Power-on/boot-up. ATTN and LAN will flash red and
then green during the power-on self-test.

ATTN

LAN

PWR

Off

Red

Green

No LAN connection due to:

- disconnected LAN cable

failure to acquire and IP address

waiting for DHCP-assigned address

ATTN

LAN

PWR

Green (Flashing)
Green

Green

Instrument Busy State

- firmware download (LAN LED red if download

over GPIB)

- lengthy instrument operation in progress

ATTN

LAN

PWR

Red (Flashing)
Green

Green

Instrument programming error or self-test error.
Error queue is read using SYSTem:ERRor?

ATTN

LAN

PWR

Off

Green (Flashing)
Green

Instrument identification. Activated from instrument
Web interface:

ON: Turn on Front Panel Interface Indicator

OFF: Turn off Front Panel Interface Indicator

Keysight U3020AD01 User's and Service Guide

Содержание U3020AD01











































Результаты поиска

Содержание U3020AD01

Отзывы:

Похожие инструкции для U3020AD01

Бренды по названию

Популярные бренды

Keysight Technologies U3020AD01, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание U3020AD01

Отзывы:

Похожие инструкции для U3020AD01

Бренды по названию

Популярные бренды