Keysight Technologies U1818A Скачать руководство пользователя страница 46

Страница: 46 / 47

Service and Maintenance

Keysight U1818A/B Operating and Service Manual

Connect ZIF probe head to ZIF tip desired for measurement. When you need to

make a measurement at a point where you’ve previously installed a ZIF tip,

insure the latch on the ZIF tip is open, insert the contacts on the probe head

into the ZIF socket, and then close the ZIF latch with a non- conductive tool.

Depending on the positioning of the ZIF tip, you may need to support the body

of the ZIF tip while closing the latch. This can be done by tweezers or other

suitable tool by grabbing the PC board at the tip while the latch is being

closed. If the circuit is live and there is concern about shorting anything out,

use plastic or non-conductive tweezers. See

Figure 2-39

Figure 2-39

Use non-conductive tool to close the latch

Содержание U1818A
















































Результаты поиска

Содержание U1818A

Отзывы:

Похожие инструкции для U1818A

Бренды по названию

Популярные бренды

Keysight Technologies U1818A, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание U1818A

Отзывы:

Похожие инструкции для U1818A

Бренды по названию

Популярные бренды