Keysight Technologies U1818A Скачать руководство пользователя страница 38

Страница: 38 / 47

Service and Maintenance

Keysight U1818A/B Operating and Service Manual

Tips for using browser probe heads

– Spring steel wires will last longer if the span is set by grabbing the lead near

the PC board edge and twisting instead of just pulling or pushing the wires

apart or together.

Tips for using solder-in probe heads

– When soldering in leads to DUT always use plenty of flux. The flux will insure a

good, strong solder joint without having to use an excessive amount of solder.

– Strain relieves the micro coax leading away from the solder-in tips using hook-

and- loop fasteners or adhesive tape to protect delicate connections.

– Note that for the differential solder- in probe head, the + and - connection can

be determined when the probe head is plugged into the probe amplifier,

therefore, it does not matter which way the tip is soldered.

Procedures and soldering tips for using N5425A InfiniiMax ZIF probe

heads

The InfiniiMax ZIF (Zero Insertion Force) Probe Heads system is a way to use a less

expensive connection accessory (ZIF tip) that can be installed at many locations

on a device under test, to connect to a probe head (N5426A) that transports the

signal to the probe amplifier. The advantages of this system are that the ZIF tip is

very small and connects to the probe head using a zero insertion force feature

allows connection without compressing the delicate wires which cannot support

this compression.
A close-up of the ZIF tip and the ZIF probe head before the probe head is inserted

into the ZIF tip is shown in

Figure 2-30

. Note that lever on the ZIF tip is shown in

the open position (pointed up) which allows the insertion of the probe head

contacts into the ZIF tip with zero insertion force.

Содержание U1818A
















































Результаты поиска

Содержание U1818A

Отзывы:

Похожие инструкции для U1818A

Бренды по названию

Популярные бренды

Keysight Technologies U1818A, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание U1818A

Отзывы:

Похожие инструкции для U1818A

Бренды по названию

Популярные бренды