Keysight Technologies S9106AC-2IF Скачать руководство пользователя страница 67

Страница: 67 / 80

6 Verify Operation

S9106AC-2IF, -4UP, and -42D 5G FR1 Multi-port Transceiver Solutions, Startup Guide

6. 2. 2 Verify X-Apps Controls S9106AC-4UP RF Ports at 3 GHz

This process verifies operation of the RF Transceiver .380 - 6 GHz,
FR1 connectors:

RF Out

➀

RF In

➁

1. On RF Transceiver 1, connect an RF loop-back cable from

RF Out

➀

RF In

➁

located on the Rugged Front Panel.

This loop-back cable is not included with the
S9106AC-4UP 5G FR1 Multi-port Transceiver.

Use a cable with two adapters (or equivalent) such as:
one 5063-1530 RF Cable, SMA (m) to SMA (m), 152.4 mm (6.0 in) and
two 1250-1250 Adapters, SMA (f) to Type-N (m)

2. If it is not already running, start the Modular TRX software and

review the interface; this interface is referred to as a Mode:

Содержание S9106AC-2IF

















































































Результаты поиска

Содержание S9106AC-2IF

Отзывы:

Похожие инструкции для S9106AC-2IF

Бренды по названию

Популярные бренды

Keysight Technologies S9106AC-2IF, Руководство для стартапов

Результаты поиска

Содержание S9106AC-2IF

Отзывы:

Похожие инструкции для S9106AC-2IF

Бренды по названию

Популярные бренды