Keysight Technologies S9106AC-2IF Скачать руководство пользователя страница 47

Страница: 47 / 80

4 Install Hardware

S9106AC-2IF, -4UP, and -42D 5G FR1 Multi-port Transceiver Solutions, Startup Guide

Item

Qty

Connection To... From...

to S9106AC-2IF labeled: "To DUT IF In" (front panel).

loop-back cable with adapters (Not included with S9106AC-2IF.)

Used during verification only; connect RF loop-back cable and adapters from
RF Out

➀

to RF In

➁

on Transceiver 1 and then Transceiver 2. This same

loop-back cable with adapters can be moved to verify the High IF ports as well
as the HD ports; see

Verify Operation

on page

RF loop-back cable with adapters (or equivalent) can be used:
one 5063-1530 RF Cable, SMA (m) to SMA (m), 152.4 mm (6.0 in)
two 1250-1250 Adapters, SMA (f) to Type-N (m)

Remove this loop-back cable from all RF ports, High IF ports,
and HD ports during normal use.

4. 2. 1 Connect Cables, LAN Cables, a Display, a Keyboard & Mouse

1. Connect cables as shown in the equipment setup above.

2. Connect LAN 1 (top) to the Site LAN at your facility.

3. Connect LAN 2 (bottom) to the E7770A CIU CONTROL

➅

(rear panel).

4. Connect a Display, Keyboard & Mouse (Not included with S9106AC-2IF).

Содержание S9106AC-2IF

















































































Результаты поиска

Содержание S9106AC-2IF

Отзывы:

Похожие инструкции для S9106AC-2IF

Бренды по названию

Популярные бренды

Keysight Technologies S9106AC-2IF, Руководство для стартапов

Результаты поиска

Содержание S9106AC-2IF

Отзывы:

Похожие инструкции для S9106AC-2IF

Бренды по названию

Популярные бренды