Keysight Technologies J-BERT M8020A Скачать руководство пользователя страница 15

Страница: 15 / 78

Keysight M8000 Series of BER Test Solutions Installation Guide

System Requirements

Hardware Configurations for M8020A

The following section describes and illustrates various setup combinations

in which you can install the M8020A modules.

M8020A Base System Configuration

The base configuration is a single channel system (a second channel can

be added with license) consisting of the 5-slot M9505A AXIe Chassis and

an M8041A module. The M8041A occupies three slots. A maximum of two

M8020A modules can be installed in a 5-slot chassis.

Figure 1

M8020A configuration for 16 Gb/s BERT with 1 to 2 channel

NOTE

The M8041A module must be installed in slots 1 through 3 of the

M9505A AXIe Chassis for proper local bus communication unless the

M9536A or M9537A AXIe Embedded Controller is installed (must be in

slot 1).

Содержание J-BERT M8020A















































































Результаты поиска

Содержание J-BERT M8020A

Отзывы:

Похожие инструкции для J-BERT M8020A

Бренды по названию

Популярные бренды

Keysight Technologies J-BERT M8020A, Руководство по установке

Результаты поиска

Содержание J-BERT M8020A

Отзывы:

Похожие инструкции для J-BERT M8020A

Бренды по названию

Популярные бренды