Keysight Technologies InfiniiMax III Series Скачать руководство пользователя страница 2

Страница: 2 / 128

Notices

No part of this manual may be reproduced in

any form or by any means (including elec-

tronic storage and retrieval or translation

into a foreign language) without prior agree-

ment and written consent from Keysight

Technologies, Inc. as governed by United

States and international copyright laws.

Manual Part Number

N2800-97010

Edition

April 2014
KeysightTechnologies, Inc.

1400 Fountaingrove Parkway

Santa Rosa, CA 95403 USA

Warranty

The material contained in this document is

provided “as is,” and is subject to being

changed, without notice, in future editions.

Further, to the maximum extent permitted by

applicable law, Keysight disclaims all war-

ranties, either express or implied, with

regard to this manual and any information

contained herein, including but not limited

to the implied warranties of merchantability

and fitness for a particular purpose. Keysight

shall not be liable for errors or for incidental

or consequential damages in connection

with the furnishing, use, or performance of

this document or of any information con-

tained herein. Should Keysight and the user

have a separate written agreement with war-

ranty terms covering the material in this

document that conflict with these terms, the

warranty terms in the separate agreement

shall control.

Technology Licenses

The hardware and/or software described in

this document are furnished under a license

and may be used or copied only in accor-

dance with the terms of such license.

Restricted Rights Legend

If software is for use in the performance of a

U.S. Government prime contract or subcon-

tract, Software is delivered and licensed as

“Commercial computer software” as defined

in DFAR 252.227-7014 (June 1995), or as a

“commercial item” as defined in FAR

2.101(a) or as “Restricted computer soft-

ware” as defined in FAR 52.227-19 (June

1987) or any equivalent agency regulation or

contract clause. Use, duplication or disclo-

sure of Software is subject to Keysight Tech-

nologies’ standard commercial license

terms, and non-DOD Departments and

Agencies of the U.S. Government will receive

no greater than Restricted Rights as defined

in FAR 52.227-19(c)(1-2) (June 1987). U.S.

Government users will receive no greater

than Limited Rights as defined in FAR

52.227-14 (June 1987) or DFAR

252.227-7015 (b)(2) (November 1995), as

applicable in any technical data.

Safety Notices

C A U T I O N .

CAUTION

denotes a

hazard. It calls attention to a proce-

dure that, if not correctly performed

or adhered to, could result in dam-

age to or destruction of the product.

Do not proceed beyond a caution

note until the indicated conditions

are fully understood and met.

W A R N I N G .

WARNING denotes a

hazard. It calls attention to a proce-

dure which, if not correctly per-

formed or adhered to, could result

in personal injury or loss of life. Do

not proceed beyond a warning note

until the indicated conditions are

fully understood and met.

Содержание InfiniiMax III Series

































































































































Результаты поиска

Содержание InfiniiMax III Series

Отзывы:

Похожие инструкции для InfiniiMax III Series

Бренды по названию

Популярные бренды

Keysight Technologies InfiniiMax III Series, Руководство пользователя

Результаты поиска

Содержание InfiniiMax III Series

Отзывы:

Похожие инструкции для InfiniiMax III Series

Бренды по названию

Популярные бренды