background image

Notices

© Keysight Technologies 2020
No part of this manual may be 

reproduced in any form or by any 

means (including electronic storage 

and retrieval or translation into a 

foreign language) without prior 

agreement and written consent from 

Keysight Technologies as governed by 

United States and international 

copyright laws.

Edition

Edition 2, May 2020
Published by:

Keysight Technologies 

1400 Fountaingrove Parkway

Santa Rosa, CA 95403-1738

United States

Warranty

THE MATERIAL CONTAINED IN THIS 

DOCUMENT IS PROVIDED "AS IS," 

AND IS SUBJECT TO BEING 

CHANGED, WITHOUT NOTICE, IN 

FUTURE EDITIONS. FURTHER, TO THE 

MAXIMUM EXTENT PERMITTED BY 

APPLICABLE LAW, KEYSIGHT 

DISCLAIMS ALL WARRANTIES, EITHER 

EXPRESS OR IMPLIED WITH REGARD 

TO THIS MANUAL AND ANY 

INFORMATION CONTAINED HEREIN, 

INCLUDING BUT NOT LIMITED TO THE 

IMPLIED WARRANTIES OF 

MERCHANTABILITY AND FITNESS FOR 

A PARTICULAR PURPOSE. KEYSIGHT 

SHALL NOT BE LIABLE FOR ERRORS 

OR FOR INCIDENTAL OR 

CONSEQUENTIAL DAMAGES IN 

CONNECTION WITH THE 

FURNISHING, USE, OR 

PERFORMANCE OF THIS DOCUMENT 

OR ANY INFORMATION CONTAINED 

HEREIN. SHOULD KEYSIGHT AND THE 

USER HAVE A SEPARATE WRITTEN 

AGREEMENT WITH WARRANTY 

TERMS COVERING THE MATERIAL IN 

THIS DOCUMENT THAT CONFLICT 

WITH THESE TERMS, THE WARRANTY 

TERMS IN THE SEPARATE AGREEMENT 

WILL CONTROL.

Technology Licenses

The hardware and/or software 

described in this document are 

furnished under a license and may be 

used or copied only in accordance with 

the terms of such license.

U.S. Government Rights

The Software is "commercial computer 

software," as defined by Federal 

Acquisition Regulation ("FAR") 2.101. 

Pursuant to FAR 12.212 and 27.405-3 

and Department of Defense FAR 

Supplement ("DFARS") 227.7202, the 

U.S. government acquires commercial 

computer software under the same 

terms by which the software is 

customarily provided to the public. 

Accordingly, Keysight provides the 

Software to U.S. government 

customers under its standard 

commercial license, which is embodied 

in its End User License Agreement 

(EULA), a copy of which can be found at 

http://www.keysight. com/find/sweula. 

The license set forth in the EULA 

represents the exclusive authority by 

which the U.S. government may use, 

modify, distribute, or disclose the 

Software. The EULA and the license set 

forth therein, does not require or 

permit, among other things, that 

Keysight: (1) furnish technical 

information related to commercial 

computer software or commercial 

computer software documentation that 

is not customarily provided to the 

public; or (2) relinquish to, or otherwise 

provide, the government rights in 

excess of these rights customarily 

provided to the public to use, modify, 

reproduce, release, perform, display, or 

disclose commercial computer software 

or commercial computer software 

documentation. No additional 

government requirements beyond 

those set forth in the EULA shall apply, 

except to the extent that those terms, 

rights, or licenses are explicitly required 

from all providers of commercial 

computer software pursuant to the FAR 

and the DFARS and are set forth 

specifically in writing elsewhere in the 

EULA. Keysight shall be under no 

obligation to update, revise or 

otherwise modify the Software. 

Safety Notices

A WARNING notice denotes a hazard. 

It calls attention to an operating 

procedure, practice, or the like that, if 

not correctly performed or adhered to, 

could result in personal injury or death. 

Do not proceed beyond a WARNING 

notice until the indicated conditions are 

fully understood and met.

A CAUTION notice denotes a hazard. 

It calls attention to an operating 

procedure, practice, or the like that, if 

not correctly performed or adhered to, 

could result in damage to the product  

or loss of important data. Do not 

proceed beyond a CAUTION notice until 

the indicated conditions are fully 

understood and met.

Содержание E9986E

























Отзывы: