Keysight Technologies E4981A Скачать руководство пользователя | Manualshive

Страница: 57 / 152

background image

Chapter 4

55

Troubleshooting

Function Specific Troubleshooting

4. T

roub

lesho

o

ting

Function Specific Troubleshooting

If the E4981A exhibits a failure symptom that is related to a specific function or control
such as a front panel key control, display, data storage, remote control interface, external
trigger, isolate the trouble using the Function Specific Troubleshooting procedures
described below. The major functions of the E4981A and the troubleshooting procedure for
each function are shown in

Table 4-4

Major functions and troubleshooting procedures

Function

Description

Troubleshooting

Front panel keys

All the E4981A functions can be set and controlled
via the front panel keys.

Refer to

“To Check the Front

Panel” on page 56

LCD

Almost all the information including the
measurement value, setup state, result data
processing, menu bar, softkey label and others are
indicated on the LCD.

Refer to

“To Check the

LCD” on page 56

Front USB port

The USB port is used to save data in a USB
memory.

Refer to

“To Check the Front

USB port” on page 56

.

External trigger input

The external trigger input terminal (BNC) on the
rear panel allows an external trigger source to be
used for measurement trigger.

Refer to

“To Check the

External Trigger Input” on
page 57

.

LAN port

The LAN interface port on the rear panel allows
the E4981A to be connected to 10/100 Base-T
Ethernet.

Refer to

“To Check the

LAN” on page 57

.

GPIB Interface

The GPIB compatibility allows the E4981A to be
operated as a talker/listener on IEEE 488 interface
bus.

Refer to

“To Check the

GPIB” on page 59

USB (USBTMC)
Interface

Through this port, you can control the E4981A via
external controllers. It is equivalent to control via
GPIB.

Refer to in

“To Check the

USB (USBTMC) Interface”
on page 60

Handler interface

The interface is for data exchange with an
automatic machine (handler) used on production
line.

Refer to in

“To Check the

Handler Interface Function”
on page 60

.

Scanner interface

The interface to connect a scanner to perform up to
128 sets of multi-channel correction and
measurements.

Refer to in

“To Check the

Scanner Interface Function”
on page 64

.

«
...
55
56
57
58
59
...
»

Содержание E4981A

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для E4981A

Бренд: Kanomax Страницы: 26

Бренд: Macnaught Страницы: 20

Бренд: Eagle Eye Страницы: 3

Бренд: VALTRONICS Страницы: 13

Бренд: JIANGSU Страницы: 8

Бренд: UEi Страницы: 8

HF Scientific AccUView LED Ex

Бренд: Watts Страницы: 2

Бренд: Kobold Страницы: 55

Бренд: RADWAG Страницы: 176

Бренд: Hanna Instruments Страницы: 2

Бренд: Zero 88 Страницы: 32

Бренд: TEA Страницы: 10

Бренд: Fluke Страницы: 22

Бренд: doble Страницы: 78

Бренд: EKF Страницы: 32

Бренд: Hioki Страницы: 288

Бренд: Eddyfi Technologies Страницы: 31

Бренд: Kemo Electronic Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды