PHASE DESCRIPTION
EXEMPLE
1
Presser sans le relâcher la touche du récepteur jusqu’à
ce que la DEL s’allume (3 secondes environ) puis s’étei-
gne (3 secondes environ). Relâcher la touche
(>3s)-> (>3s)->
2
Environ une seconde après que la touche a été relâchée,
la DEL présente sur le récepteur commence à clignoter
(1s)+ (1s)+
3
Presser la touche du récepteur au troisième clignotement
4
Si l’effacement a été correctement effectué, le récep-
teur émettra 1 clignotement long
5 - RÉCEPTION ET MISE EN SERVICE
L’installation peut être mise en service après l’essai de réception confié à un technicien
qualifié, qui doit effectuer les essais prescrits par la norme de référence en fonction
des risques présents et s’assurer que l’installation est conforme aux dispositions des
normes.
GB
6.4 - PROGRAMMING THE OPERATING TIMEOUT
WARNING: The maximum operating time in MOTOR mode is 6 minutes. The
default operating time in motor mode is 4 minutes.
7 - COMMON FUNCTIONS
7.1 - LEARNING AN ADDITIONAL TRANSMITTER USING A
TRANSMITTER ALREADY IN THE MEMORY
The remote copy procedure must be carried out in the area served by the receiver.
7.2 - TOTALLY CLEARING THE MEMORY
7.3 - CLEARING ALL THE TRANSMITTERS FROM THE MEMORY
7.4 - DELETING A SINGLE TRANSMITTER
PH. DESCRIPTION
EXAMPLE
1
Press the control unit programming pushbutton quickly.
The LED blinks and the buzzer sounds every 2 seconds.
>1
x 1+ x 1
2
Hold the programming pushbutton for more than 3
seconds. The control unit LED blinks once and the buzzer
sounds.
>3s
x 1+ x 1
3
Press the control unit programming pushbutton a number
of times equal to the number of operating minutes to be
programmed:
first press = 0 minutes
second press = 1 minute
third press = 2 minutes
fourth press = 3 minutes
fifth press = 4 minutes
sixth press = 5 minutes
seventh press = 6 minutes
The control unit gives 3 blinks and 3 beeps each time the
pushbutton is pressed.
> n
x 3+ x 3
4
Confirm the operating minutes by pressing the program
-
ming pushbutton and holding it for more than 3 seconds.
The control unit will give one long blink and one long
confirmation beep.
>3s
x 1+ x 1
5
Press the control unit programming pushbutton a number
of times equal to the number of operating seconds to be
programmed:
first press = 1 second
second press = 2 seconds
…..
fifty-ninth press = 59 seconds
The control unit gives 4 blinks and 4 beeps each time the
pushbutton is pressed.
> n
x 4+ x 4
6
Confirm the operating seconds by pressing the program
-
ming pushbutton and holding it for more than 3 seconds.
The control unit will give one long blink and one long
confirmation beep.
>3s
x 1+ x 1
PH. DESCRIPTION
EXAMPLE
1
Press and hold the control unit programming pushbutton
until the LED blinks once and the buzzer sounds.
>3s
x 1+ x 1
2
About 1 second after the key is released, the LED blinks
5 times.
x 5
3
Press the key on the control unit as the LED blinks for the
third
time.
x 3
4
If the deletion has been successful, the receiver will give 3
short blinks and 3 beeps.
x 3+ x 3
PH. DESCRIPTION
EXAMPLE
1
Press and hold the control unit programming pushbutton
until the LED blinks once and the buzzer sounds.
>3s
x 1+ x 1
2
About 1 second after the key is released, the LED blinks
5 times.
x 5
3
Press the key on the control unit as the LED blinks for the
fourth
time.
x 4
4
If the deletion has been successful, the receiver will give 5
short blinks and 5 beeps
x 5+ x 5
PH. DESCRIPTION
EXAMPLE
1
Press and hold the control unit programming pushbutton
until the LED blinks once and the buzzer sounds.
>3s
x 1+ x 1
2
About 1 second after the key is released, the LED blinks
5 times.
x 5
3
Press the key on the control unit as the LED blinks for the
fifth
time.
x 5
4
Press the pushbutton of the transmitter to be deleted.
5
If the deletion has been successful, the receiver will give 5
short blinks and 5 beeps.
x 5+ x 5
6
To delete an additional transmitter, repeat point 5.
7
To terminate the procedure, wait for the 10 second
timeout.
PH. DESCRIPTION
EXAMPLE
1
Press the key of the new transmitter to be saved for at
least 5 seconds.
>5s
2
The control unit will not give any feedback.
3
Press the key of the old transmitter to be copied for at
least 3 seconds. (If phase 1 has been successful, the
automation system will not respond).
>3s
4
The control unit gives 1 blink and 1 beep.
x 1+ x 1
5
Press the key of the new transmitter to be saved for at
least 3 seconds.
>3s
6
The control unit gives 2 blinks and 2 beeps.
x 2+ x 2
7
Press the key of the old transmitter to be copied, holding
it down for at least 3 seconds, to confirm and quit the
programming mode.
>3s
8
The control unit gives 3 blinks and 3 beeps.
x 3+ x 3
Note The new transmitter saved has the same functions
as the transmitter already in the memory.
