background image

12

Zubehör

Accessories

Achtung!
Handauslösung

, wenn das

nur betätigen

Gestell mit dem vorgegebenen Gewicht
belastet ist.

Attention!
Activate lever

if the base

only

carries the specified weight.

!

Falls der Tisch mit mehr als 15 kg belastet wird, kann dieser bei Betätigung der Handauslösung nach unten
sacken. Der Komfortbereich geht von 5 kg bis

die Optimalbelastung liegt bei 10 kg. Falls die

max.15 kg,

Belastung zu stark ist,

Dazu

der Tisch in die oberste Position

muss

können Sie die Zusatzfeder tauschen.

Die Montage ist nur von fachkundigem Personal auszuführen.

gefahren werden.

If the table carries more than 15 kg, it may sag down when the handrelease is triggered. The comfort zone
ranges from 5 kg to

the optimal load is 10 kg. If the load is too high supplementary spring can be

max. 15 kg,

changed.

The assembly has to be carried

For this purpose the table

be moved into top position.

must

out by competent personnel only.

Zubehör

Accessories

KESSEBÖHMER

873800290 0000

13

Bitte beachten Sie den bei der

igepackten Hinweiszettel.

Zusatzfeder be

Please take notice of the information leaflet enclosed with the supplementary spring.

Bitte eine Hand mit leichtem Druck auf
die Tischplatte legen, mit der anderen
Hand die Handauslösung betätigen, bis
die optimale Position eingestellt ist.

Slightly press one hand onto the tabletop
and activate lever with the other
hand until the optimal position has been
found.

TM RQ70 MOTOR

TM Q71/500 Liftgestell

TM Q71/500 Lift base

1

7

10

2 3 4

12

5 6     8 9

13 14 15 16

11

Содержание TM Q71/500

















Отзывы: