background image

IMPORTANT NOTES:

1)

This manual is valid for the following Model and associated serial numbers:

MODEL

SERIAL NO.

REV. NO.

2)

A Change Page may be included at the end of the manual. All applicable changes and
revision number changes are documented with reference to the equipment serial num-
bers. Before using this Instruction Manual, check your equipment serial number to identify
your model. If in doubt, contact your nearest Kepco Representative, or the Kepco Docu-
mentation Office in New York, (718) 461-7000, requesting the correct revision for your
particular model and serial number.

 
3)

The contents of this manual are protected by copyright. Reproduction of any part can be
made only with the specific written permission of Kepco, Inc. 

 
 

Data subject to change without notice.

KEPCO

®

  

THE POWER SUPPLIER™

MODEL

 

O P E R ATO R ’ S   M A N U A L

KEPCO INC.

KEPCO, INC.  

  131-38 SANFORD AVENUE  

  FLUSHING, NY. 11355 U.S.A.  

  TEL (718) 461-7000  

  FAX (718) 767-1102

email: [email protected]  

  World Wide Web: http://www.kepcopower.com

An ISO 9001 Company.

HSF 300W

©2015, KEPCO, INC
P/N 228-1697-r4

 

 

HSF (M, MZ) 300W

 POWER SUPPLY

HSF 300W, M and MZ Models

POWER SUPPLY

SINGLE OUTPUT METERED POWER SUPPLIES

SINGLE PHASE, POWER FACTOR CORRECTED

UNIVERSAL AC INPUT

HSF 5-60M, HSF12-27M, HSF 15-22M, 

HSF 24-14M, HSF 28-12M, HSF 48-7M

HSF12-27MZ, HSF 15-22MZ, 

HSF 24-14MZ, HSF 28-12MZ, HSF 48-7MZ

Содержание HSF 15-22M



















Отзывы: