Kenwood TS-480 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 59

background image

27

Listed below are the filter bandwidths (unit: Hz) that can be chosen; default values are shown in
bold.

CW

WIDTH

50 80 100 200 300 400 500

600

1000 2000

FSK

WIDTH

250 500 1000

1500

When the optional CW filters are installed, the TS-480 will automatically select the optimum IF filter
in accordance with the DSP filter bandwidth.
Also available are filters for PSK31 and RTTY data mode operations. From the menu, if you select
ON for the “Available data communications filters”, these data communications filters can be used
in SSB mode. You can choose from 3 center frequencies and 7 WIDTH settings.
Listed below are the filter types (unit: Hz) that can be chosen; default values are shown in bold.

For data

communications

Center

1000 1500

2210

WIDTH

50 100 250

500

1000 1500 2400

During PSK31 operations, the center frequency is set to either 1000Hz or 1500Hz.
Furthermore, since it is now possible to select an optional CW IF filter in SSB mode, it is possible
to narrow the bandwidth.

Interference

Interference

Interference

Interference

Target signal

Target signal

Fig. 21: Switching WIDTH

during CW operations

«
...
25
26
27
28
29
...
»

Содержание TS-480




























































Отзывы:

Нет отзывов

Похожие инструкции для TS-480

Бренд: Panasonic Страницы: 7

Бренд: Easy wave Страницы: 2

Бренд: Yamaha Страницы: 128

Бренд: Yamaha Страницы: 147

Бренд: RKI Instruments Страницы: 65

Sat-Light 7410F

Бренд: Foxcom Страницы: 74

BTL6-A 5 00-M0500-PF-S115

Бренд: Balluff Страницы: 22

Бренд: HBK Страницы: 40

Бренд: HBK Страницы: 104

Бренд: Icom Страницы: 56

Бренд: Xoro Страницы: 78

Бренд: Icom Страницы: 101

Бренд: Sansui Страницы: 50

Бренд: Target Страницы: 10

Бренд: E+E Elektronik Страницы: 16

Бренд: Aiphone Страницы: 4

Бренд: D+M Group Страницы: 19

Бренд: Cable AML Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды