Kenwood TS-480 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 59

background image

10

SPS (separate power sources) [TS-480HX only]

SPS is shorthand for “operating at 200W using two 100W 13.8V power sources.” To generate a
200W output from 13.8V requires a maximum (total) current of 41A. As previously explained, the
TS-480HX employs a pair of 100W final amps. What the SPS design does is to supply these
amps from two separate power supplies, as shown in Fig. 3 below.
The use of two power supplies may appear inconvenient, but in actual fact this arrangement is
quite practical. Many customers already possess a 100W class power supply, so when they
acquire this 200W transceiver they do not have to make an additional purchase of a new 200W
class power supply. It is possible for them to make use of the 100W unit in their possession.
The PS-53 power supply is specified for the TS-480; however, as long as it can produce 20.5A or
more continuously at 13.8V, other power supplies can be used. Also, it is possible to operate this
transceiver using a single power supply that can produce at least 41A continuously; note, however,
that two power cables would still be needed.

Fig. 3: SPS schematic diagram

Other circuits

DC power

supply 1

(13.8V,

≥

20.5A)

DC power

supply 2

(13.8V,

≥

20.5A)

Final amp 1

Final amp 2

Drive amp

DC1 connector

DC2 connector

Chassis

«
...
8
9
10
11
12
...
»

Содержание TS-480




























































Отзывы:

Нет отзывов

Похожие инструкции для TS-480

Бренд: MAGNELAB Страницы: 2

Бренд: Handic Страницы: 21

Бренд: Panasonic Страницы: 7

Бренд: Daspi Страницы: 2

Бренд: M-system Страницы: 4

Бренд: L&S Страницы: 5

Бренд: Watkins Johnson Страницы: 9

Бренд: Danfoss Страницы: 2

Бренд: Immersion Страницы: 5

Бренд: Target Страницы: 10

Бренд: Rohde & Schwarz Страницы: 199

Бренд: Spektrum Страницы: 16

DIGITAL TO TV DT-301

Бренд: Promax Страницы: 4

Бренд: afx light Страницы: 15

Бренд: IMG STAGELINE Страницы: 24

Бренд: Easy wave Страницы: 8

Бренд: PR electronics Страницы: 28

Бренд: Sirius Satellite Radio Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды