![Kenwood TS-2000 Скачать руководство пользователя страница 99](http://html.mh-extra.com/html/kenwood/ts-2000/ts-2000_service-manual_1955640099.webp)
100
TS-2000/X
CN49
CN18
CN10
CN1
B. Flat cable (16P)
(E37-0572-05)
About 17cm
A. Lead wire with
minipin plug
(E37-0878-05)
About 56cm
Service Jig
■
How to use
ADJUSTMENT
A. Lead wire with minipin plug
B. Flat cable (16P)
Adjustment Mode
■
Outline
1. The TS-2000/X can be adjusted manually (by turning a
coil, trimmer, etc.) or by setting the service adjustment
mode (adjustment with panel keys). In the service ad-
justment mode (simply referred to as the adjustment
mode below), adjustments items are shown in menu
No.00 to 126 and all data are saved in the EEPROM (X53-
391: IC7).
2. To enter adjustment mode, the user firmware in the main
unit must be rewritten with adjustment firmware. (The
user firmware is factory-set.)
■
Diagram of uploading the adjustment firmware
1. Checksum confirmation
Switch the transceiver on while pressing and hold [N.R.]
and [MIC/CAR] keys.
2. Preparation of uploading the data
1) Access Menu No. 56 and select 9600 bps, then switch the
transceiver OFF.
Turn the transceiver ON again.
2) Back up the user data in the transceiver (Menu configura-
tion and Memory channel data)
Run the programming software (W05-0855-00), then select
“Menu/MRch READ from RADIO”
Name the file that can be identified easily.
(Such as a serial number)
3. Uploading the adjustment firmware
1) Turn the switch (S1) ON in TX-RX1 unit (X57-605 A).
2) Upload the adjustment firmware, using “ADJUST FIRM-
WARE WRITE” menu.
3) Turn the switch (S1) OFF in TX-RX1 unit (X57-605 A).
4) Turn the transceiver ON while pressing [A=B] key to
perform the full reset.
4. Repair and adjustment
5. Uploading the user firmware
1) Turn the switch (S1) ON in TX-RX1 unit (X57-605 A).
2) Upload the user firmware, using “USER FIRMWARE
WRITE” menu.
3) Turn the switch (S1) OFF in TX-RX1 unit (X57-605 A).
4) Turn the transceiver ON while pressing [A=B] key to
perform the full reset.
6. Checksum confirmation
Switch the transceiver on while pressing and hold [N.R.]
and [MIC/CAR] keys.
If the user firmware has not changed, the checksum is
same as the value in step 1.
If the user firmware has been updated, the checksum
should match the new checksum.
7. Uploading the user firmware
1) Turn the transceiver ON while pressing [A=B] key to per-
form the full reset.
2) Run the programming software (W05-0855-00), then select
“Menu/MRch WRITE to the RADIO”
Refer to the
uploading
procedure
1~8.
Refer to the
uploading
procedure 9.
Refer to the
uploading
procedure 10.
Содержание TS-2000
Страница 132: ...TS 2000 X TS 2000 X 134 WIRING ...
Страница 142: ...1 2 B A D F C E G I H J 3 5 7 9 4 6 8 10 12 14 11 13 TS 2000 X CIRCUIT DIAGRAM 165 ...
Страница 144: ...1 2 B A D F C E G I H J 3 5 7 9 4 6 8 10 12 14 11 13 TS 2000 X CIRCUIT DIAGRAM 169 ...
Страница 167: ...234 TS 2000 X MC 52DM MULTI FUNCTION MICROPHONE WITH DTMF Schamatic Diagram ...