background image

KENWOOD CORPORATION

   

TK-3180-K2, TK-3180-K4 

FCC ID:ALH37333120  IC:282D-37333120

 

 

<Front Side> 

NO. Name 

Description 

1 S 

Programmable 

 

default: 

None 

2 A 

Programmable 

default: 

None 

<B 

Programmable default: 

CH/GID 

Down 

C> 

Programmable default: 

CH/GID 

Up 

 
LED 

NO. Name 

Description 

  LED 

The LED is three colors. 
Lights green while receiving at user mode. Light red while transmitting, 
flashes red when the battery power is low while transmitting .Lights 
orange when individual called. 

 
 
 
TERMINAL 
Universal connector 
      Universal connector covering for blindfold mode of resin is possible. 
 

NO. Name 

Description 

I/O 

SSW 

Ext/Int Speaker Switch Input 

SP+ 

BTL  for External Speaker 

SP- 

BTL Output - for External Speaker 

MSW 

Ext/Int MIC Switch Input 

EMC 

External MIC Input 

ME 

External MIC GND 

7 PTT 

External 

PTT 

Input 

PF 

Programable Function Key Input 

OPT 

Aux I/O port 

I/O 

10 E 

GND 

11 5U 

5V 

12 TXD 

Serial 

Data 

Output 

13 RXD 

Serial 

Data 

Input 

14 NC(E) 

Not 

use 

 
 
Battery Terminal 

It’s type of spring plate. The minus terminal connect to chassis ground 
It’s mounted rear side of radio and mounting instruction is slide method. 

 
OTHER 
Rear 

A rail and a hook for battery installation. 
Space which affixes name plate.Model name plate 
Screw hole for belt hook installation. 

 
Bottom 
Battery release lever 

Содержание TK-3180











Отзывы: