background image

KENWOOD CORPORATION

   

TK-3180-K2, TK-3180-K4 

FCC ID:ALH37333120  IC:282D-37333120

 

 

ATTENTION (U.S.A. Only): 

The RBRC Recycle seal found on 

KENWOOD 

nickel-cadmium (Ni-Cd) battery packs 

indicates 

KENWOOD

’s voluntary participation in an industry program to collect and 

recycle Ni-Cd batteries after their operating life has expired. The RBRC program is an 
alternative to disposing Ni-Cd batteries with your regular refuse or in municipal waste 
streams, which is illegal in some areas. 
For information on Ni-Cd battery recycling in your area, call (toll free) 
1-800-8-BATTERY (1-800-822-8837). 

KENWOOD

’s involvement in this program is 

part of our commitment to preserve our environment and conserve our natural 
resources. 

 
 

UNPACKING AND CHECKING EQUIPMENT

 

Note:  

The following unpacking instructions are for use by your 

KENWOOD 

dealer, an authorized 

KENWOOD 

service facility, or the factory. 

Carefully unpack the transceiver. We recommend that you identify the items listed in the following table before 
discarding the packing material. If any items are missing or have been damaged during shipment, file a claim with the 
carrier immediately. 

 

§  Accessories 
 

Quantity 

Item 

Part Number 

Instruction Manual 

B62 -1759 - *0 

Belt Clip 

J29 - 0710 -*5 

Screw 

N30 - 3008 - 60 

Cap 

B09 - 0625 - *3 

Screw 

N08 - 0548 - *4 

Содержание TK-3180











Отзывы: