TK-3178
(
L
)
7
REALIGNMENT /
模式组合
6. Firmware Programming Mode
6-1. Preface
Flash memory is mounted on the transceiver. This allows
the transceiver to be upgraded when new features are re-
leased in the future. (For details on how to obtain the fi rm-
ware, contact Customer Service.)
6-2. Connection Procedure
Connect the transceiver to the personal computer with
the interface cable (KPG-22/22A). (Connection is the same
as in the PC Mode.)
6-3. Programming
1. Start up the fi rmware programming software (Fpro.exe).
2. Set the communications speed (normally, 115200 bps)
and communications port in the confi guration item.
3. Set the fi rmware to be updated by File name item.
4. Turn the transceiver power ON with the [Side2] key held
down. Then, the orange LED on the transceiver lights and
“PROG 115200” is displayed.
5. Check the connection between the transceiver and the
personal computer, and make sure that the transceiver is
in the Program mode.
6. Press write button in the window. When the transceiver
starts to receive data, the “PG” display is blinking.
7. If writing ends successfully, the checksum is calculated
and a result is displayed.
8. If you want to continue programming other transceivers,
repeat steps 4 to 7.
Note:
This mode cannot be entered if the Firmware Program-
ming mode is set to Disable in the Programming soft-
ware.
6-4. Function
1. If you press the [Side2] key while “PROG 115200” is
displayed, the display changes to “PROG 19200” to in-
dicate that the write speed is low speed (19200 bps). If
you press the [Side2] key again while “PROG 19200”
is displayed, the display changes to “PROG 38400”. If
you press the [Side2] key again while “PROG 38400” is
displayed, the display changes to “PROG 57600”. If you
press the [Side2] key again while “PROG 57600” is dis-
played, the display returns to “PROG 115200”.
2. If you press the [Side1] key while “PROG 115200” is
displayed, the checksum is calculated, and a result is
displayed. If you press the [Side1] key again while the
checksum is displayed, “PROG 115200” is redisplayed.
Note:
Normally, write in the high-speed mode.
6. 固件编程模式
6-1. 前言
闪存被安装在手持对讲机上。当将来出现新功能时，允许
手持对讲机升级。( 要了解如何获得固件的详细情况，请与供
应商联系。)
6-2. 连接步骤
使用编程电缆 ( K P G -22/22A ) 将手持对讲机与计算机连接。
( 与计算机编程模式中的连接方法一样。)
6-3. 编程
1. 启动固件编程软件 (FPRO.exe)。
2. 在配置项中设定通信速率 ( 通常为 115200bps) 和通信端口。
3. 在文件名称项中选定新固件。
4. 向下按动 [ S i d e2] 键并接通手持对讲机的电源。向下按住
键直到显示器出现“P R O G115200”为止。然后，手持对讲
机上的橙色 LED 点亮，并显示“PROG 115200”
。
5. 检查手持对讲机与个人电脑之间的连接是否正确，并且确
认手持对讲机是否处于编程模式。
6. 按窗口中的写入按钮。手持对讲机开始接收数据时，
“P G”
显示不断闪烁。
7. 如果写入成功结束，则计算校验和并显示结果。
8. 如果用户需要继续编程其他的手持对讲机，
重复步骤 4 到 7。
注释∶
如果在编程软件 ( K P G -127D ) 中固件编程模式设定为禁用，
则不能进入此模式。
6-4. 功能
1. 如果在显示“PROG 115200”时按 [Side2] 键，则显示变为
“PROG 19200”以表示写入速度为低速 (19200bps)。如果在
显示“PROG 19200”时再次按 [Side2] 键，
则显示变为“PROG
38400”
。如果在显示“PROG 38400”时再次按 [Side2] 键，
则显示变为“PROG 57600”
。如果在显示“PROG 57600”时
再次按 [Side2] 键，则显示返回到
“PROG 115200”
。
2. 如果在显示“PROG 115200”时按 [Side1] 键，则计算校验
和并显示结果。如果在显示校验和时再次按 [ S i d e1] 键，
则重新显示“PROG 115200”
。
注释∶
通常以高速模式写入。
