Kenwood ProTalk NX-P500 Скачать руководство пользователя страница 7

Страница: 7 / 68

CAUTION

◆

Always switch OFF a transceiver equipped with a battery pack before inserting the

transceiver into the charger.

◆

Always remove the AC adapter from an AC outlet before attempting to inspect or clean

the charger. Removing the battery packs or changing the controls does not remove

the AC voltage from the charger.

◆

Position the AC adapter cable so it will not be stepped on, tripped over, nor subjected

to damage.

◆

Always remove the AC adapter from an AC outlet by pulling on the adapter rather than

the cable.

◆

Do not use the charger if it has a damaged AC adapter or adapter cable, or if the

charger has been damaged in any way. Contact your

KENWOOD

dealer to replace or

repair the damaged part.

When charging is completed, the indicator flashing green. Remove the battery

pack or the transceiver from the charging slot of the charger.

• It takes approximately 4.5 hours to charge the battery pack.
• When the charger will not be used for a long time, unplug the AC adapter

from the AC outlet.

Note:

◆

The ambient temperature should be between 41°F and 104°F (5°C and 40°C) while
charging is in progress. Charging outside this range may not fully charge the battery.

◆

The battery pack life is over when its operating time decreases even though it is fully and

correctly charged. Replace the battery pack.

LED Status

Indicator color

Meaning

Light Red

A transceiver is in the charging slot and charging has

started.

Flashing Red

the battery pack is either defective or the battery pack

contacts are not properly mated with those of the

charger.

Flashing Green

Charging is completed; remove the battery pack from

the charger.

Alternates flashing green and

orange

The temperature of the battery pack has not satisfied

the charging start temperature. Remove the battery

pack from the charger and wait until it reaches a

normal temperature before charging it again.

Содержание ProTalk NX-P500





































































Результаты поиска

Содержание ProTalk NX-P500

Отзывы:

Похожие инструкции для ProTalk NX-P500

Бренды по названию

Популярные бренды

Kenwood ProTalk NX-P500, Руководство пользователя

Результаты поиска

Содержание ProTalk NX-P500

Отзывы:

Похожие инструкции для ProTalk NX-P500

Бренды по названию

Популярные бренды