Kenwood NX-1000 Series Скачать руководство пользователя страница 41

Страница: 41 / 86

Maintenance

[Analog/ NXDN/ DMR]

Allows you to display the signal strength and Bit Error Rate (BER) on the LCD
when constructing the system or during maintenance.

PF Button:

Press the programmed button to enter Maintenance Display Mode.

Menu Mode:

Select “MAINT” and press the

[ S ]

button to enter Maintenance

Display Mode.

Press the

[ <B ]

and

[ C> ]

buttons to select Signal strength (RSSI Level) or

BER.

Signal strength (RSSI Level: dBm)

Bit Error Rate

• BER display is available on NXDN/ DMR channel.
• When the signal strength is less than -120 dBm, “

” is displayed.

• When BER measurement is impossible, “

” is displayed.

Press the

[ S ]

button to confirm and exit mode.

Содержание NX-1000 Series























































































Результаты поиска

Содержание NX-1000 Series

Отзывы:

Похожие инструкции для NX-1000 Series

Бренды по названию

Популярные бренды

Kenwood NX-1000 Series, Руководство пользователя

Результаты поиска

Содержание NX-1000 Series

Отзывы:

Похожие инструкции для NX-1000 Series

Бренды по названию

Популярные бренды