(No.RA015<Rev.002>)1-11
•
Front panel programming mode flow chart
NX-5300
Input Password
Front panel Programming mode
t
c
e
l
e
S
e
n
o
Z
?
e
g
n
a
h
C
s
i
h
T
p
e
e
K
t
c
e
l
e
S
l
e
n
n
a
h
C
e
m
a
N
l
e
n
n
a
h
C
Transmit Power
Low
Medium
High
Blank Channel
Select the setting channel.
Zone-Channel Format
is "Personality".
"System Type = Conventional"
there is more than two.
System Select
Analog
P25
RX Frfequency
F
F
O
y
c
n
e
u
q
e
r
F
X
T
g
o
l
a
n
A
e
p
y
T
l
e
n
n
a
h
C
12.5kHz
25.0kHz
20.0kHz
When the KPG-D1N is used, 25.0kHz may not be allowed
depends on the frequency (F2, F3, F5, F6, K2, K3, K5, K6 types only).
Channel Spacing
12.5kHz
RX Signaling
OFF
QT
DQT N
DQT I
TX Signaling
OFF
QT
DQT N
DQT I
RX NAC
TX NAC
Talkgroup ID List Number
P25
NXDN
[Channel Type]:
"P25","Mixed"(Transmit Mode:P25) and
when two kinds of Channel Type is set.
[Channel Type]: "Analog"
[TX Frequency]: "OFF"
[Channel Type]: "Analog"
[Channel Type]: "Analog","Mixed"(Transmit Mode: NXDN),
"Mixed"(Transmit Mode: P25) and when a kind of Channel Type is set.
[TX Frequency]: Other than "OFF"
[Channel Type]: "Analog","Mixed"(Transmit Mode: NXDN),"Mixed"(Transmit Mode: P25)
Clone/Front Panel Password
[TX Frequency]: Other than "OFF"
[Channel Type]: "P25","Mixed"(Transmit Mode: P25)
Talkgroup List ID Amount: 0
[Channel Type]: "P25","Mixed"(Transmit Mode: P25)
Talkgroup ID List Amount must not be 0.
RX RAN
TX RAN
NXDN
[TX Frequency]: "OFF"
[Channel Type]: "P25"
[System Type]: "P25"
[System Type]: "NXDN"
6.25Hz
[Channel Type]: "NXDN","Mixed"(Transmit Mode: NXDN)
[ ]
[ ]
[ ] or [ ]
[No]
[No]
[Channel Type]: "Analog","Mixed"(Transmit Mode: NXDN),"Mixed"(Transmit Mode: P25)
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[ ]
[TX Frequency]: Other than "OFF"
[Channel Type]: "NXDN","Mixed"(Transmit Mode: NXDN)
[Channel Type]: "NXDN",
"Mixed"(Transmit Mode:NXDN) and
when two kinds of Channel Type is set.
[ ]
[ ]
[ ]
[TX Frequency]: "OFF"
[Channel Type]: "NXDN"
[ ]
[Channel Type]: "NXDN",
"Mixed"(Transmit Mode: NXDN)
[ ]
[ ] or [ ]
[ ] or [ ]
[ ] or [ ]
Mixed
[System Type]: "P25" or ”NXDN” and [Channel Type]: "Mixed"
[ ] or [ ]
[ ] or [ ]
[ ] or [ ]
[ ] or [ ]
[ ] or [ ]
[ ] or [ ]
[ ] or [ ]
[ ] or [ ]
[ ] or [ ]
[ ] or [ ]
Enter the Front panel programming mode
by using section "2.2.2 How to Enter Each Mode".
[ ]
Note:
P25 can be configured for System Select or Channel Type if one or
more P25 conventional system is preconfigured by the FPU.
Zone-Channel Format allows you to whether to configure for
each zone the channels in the same system, or channels in different system.
[ ] or [ ]
[ ] or [ ]
Transmit Mode select
g
o
l
a
n
A
P25
NXDN
[System Type]: "P25"
[System Type]: "NXDN"
[ ] or [ ]
[ ] or [ ]
[ ] or [ ]
[ ] or [ ]
[Channel Type]: "Mixed" and
when Channel Spacing in two kinds of Channel Type is set.
