English
|
11
Rock
"Rock"
Pops
"Pops"
Easy
"Easy"
Top 40
"Top40"
Jazz
"Jazz"
• User memory: The values set on the 'Audio Control'
(page 11).
• Each setting value is changed with the 'Speaker
Setting' (page 11).
First, select the speaker type with the Speaker setting.
Audio Control
1
Select the source for adjustment
Press the [SRC] button.
2
Enter Audio Control mode
Press the [AUD] button for at least 1 second.
3
Select the Audio item for adjustment
Press the [FM] or [AM] button.
Each time the button is pressed the items that
can be adjusted switch as shown below.
4
Adjust the Audio item
Press the [
4
] or [
¢
] button.
Adjustment Item
Display
Range
Bass Center Frequency*²
"Bass F"
60/70/80/100 or 150 Hz
Bass level
"Bass"
–8 — +8
Bass Q Factor*²
"Bass Q"
1.00/1.25/1.50/2.00
Bass Extend*²
"Bass EXT"
ON/OFF
Middle Center Frequency*² "MID F"
0.5/1.0/1.5/2.0 kHz
Middle level
"Middle"
–8 — +8
Middle Q Factor*²
"Middle Q"
1.0/2.0
Treble Center Frequency*² "TRE F"
10.0/12.5/15.0/17.5 kHz
Treble level
"Treble"
–8 — +8
Balance
"Balance"
Left 15 — Right 15
Fader
"Fader"
Rear 15 — Front 15
Sub woofer level*¹
"SW Level"
–15 — +15
Front High Pass Filter*²
"HPF F"
Through/100/125/
170 Hz
Rear High Pass Filter*²
"HPF R"
THRU/200 Hz
Front/Rear High Pass Filter "HPF"
THRU/100/125/170 Hz
Sub woofer Low Pass
Filter*¹
"LPF SW"
50/80/120/THRU Hz
Volume offset
"V-offset"
–8 — ±0
Loudness
"LOUD"
ON/OFF
• According to the Bass Q Factor setting value, the
frequencies that can be set in Bass Center Frequency
change as shown below.
Bass Q Factor
Bass Center Frequency
1.00/1.25/1.50
60/70/80/100
2.00
60/70/80/150
• When the Bass Extend is set to ON, low frequency
response is extended by 20%.
• Volume offset: Each source’s volume can be set as a
difference from the basic volume.
• Loudness: Compensating for low and high tones
during low volume.
• *¹ You can control this item when 'Switching preout'
(page 26) is set to "SWPRE Sub-W".
• *² Function of the KDC-X579
5
Exit Audio Control mode
Press the [AUD] button.
Speaker Setting
Fine-tuning so that the System Q value is optimal
when setting the speaker type.
1
Enter Standby
Press the [SRC] button.
Select the "STANDBY" display.
2
Enter Speaker Setting mode
Press the [Q] button.
3
Select the Speaker type
Press the [
4
] or [
¢
] button.
Each time the button is pressed the setting
switches as shown below.
Speaker type
Display
OFF
"SP OFF"
For 5 & 4 in. speaker
"SP 5/4inch"
For 6 & 6x9 in. speaker
"SP 6*9/6inch"
For the OEM speaker
"SP O.E.M."
4
Exit Speaker Setting mode
Press the [Q] button.
B64-2695-00̲U.S(K)̲02.Indd 11
03.11.18, 4:52:24 PM
