Kenwood KAC-PS811D Скачать руководство пользователя страница 5

Страница: 5 / 28

English

Controls

Fuse (25 A × 3)

Battery terminal

Ground terminal

Power control terminal

Controls the unit ON/OFF.

NOTE

Controls the unit power. Be sure to connect it with all the systems.

Speaker output terminals

As this unit accepts speakers with a minimum impedance of 1 ohm, connect

speakers with 1-ohm or higher impedance to these terminals.

CAUTION

The rated input of the speakers should be no less than the maximum output

of the amplifier. Otherwise malfunction may result.

RCA cable ground lead terminal

When using an RCA cable with a ground lead attached, connect the ground

lead to this terminal.

ID NUMBER switch

Sets an amp identification number (ID) to be used for amplifier control from

the Center Unit.

Assign ID Number "0" to an amplifier when you use it as the Master amplifier.

Assign ID Numbers "1" to "7" to amplifiers when you use them as Slave

amplifiers. Do not duplicate these numbers.

NOTE

After you have changed ID numbers of amplifiers, turn Off the POWER switch

of the Center Unit and turn it On again.

TO H/U terminal

After you have set the Master amplifier, connect it to the Center Unit.

REMOTE terminals

Used to connect to Slave amplifiers.

RESET button

Resets the microprocessor of the unit.

NOTE

The values you have set with the Amplifier Control are NOT reset.

LINE IN terminal

LINE OUT terminal

The signal that’s input from the line input terminal is output.

Power indicator

Lights when the POWER switch is turned On.

The indicator flashes several seconds when the POWER switch is turned On

or when the Protection function is activated.

INPUT SENSITIVITY control

Set this control according to the pre-output level of the center unit

connected with this unit.

NOTE

For the pre-output level, refer to the "Specifications" in the instruction manual

of the center unit.

AMP CONT (amplifier control) switch

Used to bypass the circuit when you do not control the sound with the

Amplifier Control.

• ON position:

Allows you to control the sound with the Amplifier Control.

• OFF position:

Bypasses the Amplifier Control circuit.

NOTE

Amplifier control is possible even while OFF.

PHASE switch

When this switch is set "180°" (Reverse) the speaker output phase is reversed.

BRF (band reject filter) switch

When this switch is set to "-6dB"/"-12dB", frequencies in the band set with the

"B.R.F. FREQUENCY" control are rejected and eliminated. The band rejection

allows to reduce resonance inside the vehicle compartment and standing

waves. (page 8)

ISF (infrasonic filter) switch

When this switch is set to "ON", the inaudible, ultralow frequencies below

the frequency set with the "ISF FREQUENCY" switch are cut off. This improves

the reproduction performance of the speakers by eliminating unnecessary

oscillations which will not become sound.

(

ISF FREQUENCY switch

Switches the cutoff frequency when the "ISF" switch is set to "ON".

)

LPF(Low-Pass Filter) FREQUENCY control

This control adjusts the frequency band output from this unit.

B.R.F. FREQUENCY control

Sets the rejection frequency when the "BRF" switch is set to "-6dB"/"-12dB".

(page 8)

��

�

��

�

� � � �

�

��

�

��

�

��

�

��

��
��

��

�

��

�

��

�

��

�

��

��
��

��

�

��

�

� � �

�

� �

�

��

3.KAC-X811D̲KE̲1US.indd

04.1.9, 0:29 PM

Содержание KAC-PS811D





























Результаты поиска

Содержание KAC-PS811D

Отзывы:

Похожие инструкции для KAC-PS811D

Бренды по названию

Популярные бренды

Kenwood KAC-PS811D, Инструкция по эксплуатации

Результаты поиска

Содержание KAC-PS811D

Отзывы:

Похожие инструкции для KAC-PS811D

Бренды по названию

Популярные бренды