KENT Edge 28B Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 46

background image

DUST AND DEBRIS COLLECTION SYSTEM

SERVICE MANUAL

ENGLISH

Edge 28B

1463165000(1)2007-02

23

VACUUM SYSTEM MOTOR DISASSEMBLY/ASSEMBLY

Disassembly

Remove the dust filter as shown in the User Manual.

Remove the hood (see the procedure in the relevant paragraph).

Remove the battery (see the procedure in the relevant paragraph).

Disconnect the vacuum fan connector (A).

Disconnect the cables (B) from the connector (C).

Remove the vacuum fan mounting screws (D).

Remove the motor and the vacuum fan (E), then remove the wiring harness (F) from the grommet (G).

Assembly

Assemble the components in the reverse order of disassembly.

E

D

D

G

B

A

F

B

C

S301601

TROUBLESHOOTING

POOR OPERATION OF THE VACUUM FAN

Possible causes:

The dust filter is clogged (clean).

The vacuum fan blades are broken/worn (replace the motor and the vacuum fan).

The hopper gaskets are worn (replace).

THE VACUUM FAN DOES NOT OPERATE

Possible causes:

There is an open in the circuit breaker (29) (replace).

There are foreign materials clogging the vacuum fan (remove the motor and the vacuum fan).

The vacuum system motor is faulty (repair/replace).

THE FILTER SHAKER DOES NOT WORK

Possible causes:

The filter shaker terminals are damaged (replace the filter shaker).

1.

2.

3.

4.

5.

6.

7.

8.

1.

2.

3.

1.

2.

3.

1.

«
...
23
24
25
26
27
...
»

Содержание Edge 28B















































Отзывы:

Нет отзывов

Похожие инструкции для Edge 28B

Бренд: SYSFORM Страницы: 28

Бренд: Ricoh Страницы: 116

Бренд: Adler Страницы: 5

Бренд: DURKOPP ADLER Страницы: 24

Бренд: Pfaff Страницы: 150

Бренд: Singer Страницы: 53

Neofold HS 1250

Бренд: Neolt Страницы: 114

Бренд: DIAKAT Страницы: 10

Бренд: Singer Страницы: 42

Sweepmaster B1500 RH

Бренд: HAKO Страницы: 70

Бренд: Fimap Страницы: 44

Бренд: Singer Страницы: 67

Бренд: Royal Sovereign Страницы: 36

Бренд: JUKI Страницы: 128

Бренд: Panasonic Страницы: 30

Бренд: Panasonic Страницы: 60

Бренд: Panasonic Страницы: 64

Бренд: Panasonic Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды