7
INSTALLATION REQUIREMENTS
KEY DIMENSIONS AND SPECIFICATIONS
CHOOSE THE PROPER LOCATION
CLEARANCES
FLOORING
WARNING
• This washer is heavy. Two or more people are
required when moving and unpacking the washer.
Failure to do so may result in damage to property or
serious bodily harm.
• Store and install the washer where it will not be
exposed to temperatures below freezing or exposed
to outdoor weather conditions.
Failure to follow this
warning can cause serious injury,
fi
re, electric shock,
or death.
• Properly ground the washer to conform with all
electric governing codes and ordinances.
Failure
to follow this warning can cause serious injury,
fi
re,
electric shock, or death.
• To reduce the risk of electric shock, do not install the
washer in humid spaces.
Failure to follow this warning
can cause serious injury,
fi
re, electric shock, or death.
•
To ensure proper air
fl
ow, do not block the large
opening on the bottom of the washer with carpeting
or other materials.
• Do not remove the ground prong. Do not use an
adapter or extension cord. Plug into a grounded
3-prong outlet.
Failure to follow this warning can cause
serious injury,
fi
re, electric shock, or death.
Power Outlet
• The power outlet must be within 60 in. (1.5 m) of either
side of the washer.
• The appliance and outlet must be positioned so that
the plug is easily accessible.
• Do not overload the outlet with more than
one appliance.
• The outlet must be grounded in accordance with
current wiring electric codes and regulations.
• Time-delay fuse or circuit breaker is recommended.
NOTE:
It is the personal responsibility and obligation of
the product owner to have a proper outlet installed by a
quali
fi
ed service technician.
To ensure su
ffi
cient clearance for water lines and air
fl
ow,
allow minimum clearances of at least 1 in. (2.5 cm) at the
sides and 4 in. (10 cm) behind the unit. Be sure to allow
for wall, door, or
fl
oor moldings that may increase the
required clearances.
Allow at least 22 in. (55.9 cm) in front of
the washer to open the door.
NOTE:
The
fl
oor must be strong and rigid enough to
support the weight of the washer, when fully loaded,
without
fl
exing or bouncing. If your
fl
oor has too much
fl
ex, you may need to reinforce it to make it more rigid.
A
fl
oor that is adequate for a top-loading washer may
not be rigid enough for a front loading washer, due to
the di
ff
erence in the spin speed and direction. If the
fl
oor is not solid, your washer may vibrate and you may
hear and feel the vibration throughout your house.
• To minimize noise and vibration, the washer MUST be
installed on a solidly constructed
fl
oor. See the NOTE
to your right.
• Allowable slope under the entire washer is a maximum
1 in. di
ff
erence from side to side or from front to back.
• Installing on carpeting and soft tile surfaces is
not recommended.
• Never install the washer on a platform or weakly
supported structure.
Description
Front-Loading
Washer
Rated Voltage/Frequency
120VAC, 60Hz
Dimensions
27 in. (W) X 29 ¾ in. (D) X 38
11
/
16
in. (H), 51 in. (D, door open)
68.6 cm (W) X 75.6 cm (D) X 98.3 cm (H), 139.5 cm (D, door open)
Net Weight
187.17 lbs (84.90kg)
21 ¼"
(54 cm)
29 3/4"
(75.6 cm)
51"
(129.5 cm)
4"
(10 cm)
1"
(2.5 cm)
27"
(68.6 cm)
1"
(2.5 cm)
