Kenmore 795.79012.901 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 37

background image

7-2 ICE MAKER FUNCTIONS

7-2-1 Ice Making Mode

1. Icemaking refers to the freezing of supplied water in the ice trays. Complete freezing is assured by measuring the

temperature of the Tray with icemaking SENSOR.

2. Icemaking starts after completion of the water fill operation.

3. The icemaking function is completed when the sensor reaches -7°C, 60 to 240 minutes after starting.

NOTE :

After icemaker power is ON, the icemaker heater will be on for test for 9 sec.

7-2-2 Harvest Mode

1. Harvest (Ice removing) refers to the operation of dropping ices into the ice bin from the tray when icemaking has

completed.

2. Harvest mode:

(1) The Heater is ON for 30 seconds, then the motor starts.
(2) Harvest mode is completed if it reaches start position again while Heater & Motor are on at the same time.

A. ice bin is full : The EJECTOR stops (heater off).
B. ice bin is not full : The EJECTOR rotates twice to open for ice.

NOTE :

If the EJECTOR does not rotate once within 5 minutes in status (2), separate heater control mode starts
operating to prevent the EJECTOR from being constrained. (It is recommended that the user open for ice to
return to normal mode.)

- 22 -

«
...
20
21
22
23
24
...
»

Содержание 795.79012.901






































Отзывы:

Нет отзывов

Похожие инструкции для 795.79012.901

Бренд: Dacor Страницы: 2

Бренд: Dacor Страницы: 20

Бренд: Dacor Страницы: 156

Бренд: Dacor Страницы: 20

Бренд: Gamko Страницы: 64

Бренд: KegLand Страницы: 13

Бренд: JUNO Страницы: 32

Бренд: Tricity Bendix Страницы: 12

Бренд: Saba Страницы: 30

Бренд: NEFF Страницы: 28

Бренд: CORBERO Страницы: 10

8.436.545.201.497

Бренд: Svan Страницы: 68

Бренд: Dometic Страницы: 46

Бренд: Gorenje Страницы: 36

Бренд: True Страницы: 2

Бренд: Tesla Страницы: 80

Бренд: Haier Страницы: 10

Бренд: Maytag Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды