background image

DANGER

USE AND CARE

• NEVER store a spare LP tank under or near grill or in 

enclosed areas

• Never fill the cylinder beyond 80% full. 
• An overfilled or improperly stored tank is a hazard due 

to possible gas release from the safety relief valve.

• If you see, smell or hear escaping gas, immediately get 

away from the LP tank/grill and call your fire 

department.

 • If the above is not followed exactly, a fire causing 

death or serious injury may occur.

LP Tank Removal, Transport And Storage

• Turn OFF all control knobs and LP tank valve. Turn coupling 

nut counterclockwise by hand only - do not use tools to 
disconnect. Lift LP tank wire upward off of LP tank collar, then 
lift LP tank up and off of support bracket. Install safety cap onto 
LP tank valve. Always use cap and strap supplied with valve. 

Failure to use safety cap as directed may result in serious 

personal injury and/or property damage. 

LP Tank Valve

Retainer Strap

Safety Cap

• A disconnected LP tank in storage or being transported must 

have a safety cap installed (as shown). Do not store an LP tank 
in enclosed spaces such as a carport, garage, porch, covered 
patio or other building. Never leave an LP tank inside a vehicle 
which may become overheated by the sun.

• Do not store an LP tank in an area where children play.

4 • 464810208

OPD Hand Wheel

LP (Liquefied Petroleum Gas)

LP gas is nontoxic, odorless and colorless when produced.

 For 

Your Safety

, LP gas has been given an odor (similar to rotten 

cabbage) so that it can be smelled. 

LP gas is highly flammable and may ignite unexpectedly when 
mixed with air.

LP Cylinder Filling

Use only licensed and experienced dealers.

LP dealer 

must purge new cylinder

 before filling.

Dealer should 

NEVER

 fill LP cylinder more than 80% of LP 

cylinder volume. Volume of propane in cylinder will vary by 
temperature.

A frosty regulator indicates gas overfill. Immediately close LP 
cylinder valve and call local LP gas dealer for assistance.

• Do not release liquid propane (LP) gas into the atmosphere. 

This is a hazardous practice.

• To remove gas from LP cylinder, contact an LP dealer or call a 

local fire department for assistance. Check the telephone 
directory under “Gas Companies” for nearest certified LP 
dealers.

LP Tank   
• The LP tank used with your grill must meet the following 

requirements:

Use LP tanks only with these required measurements: 12" 
(30.5cm) (diameter) x 18" (45.7 cm) (tall) with 20 lb. (9 kg.) 
capacity maximum.

• LP tanks must be constructed and marked in accordance with 

specifications for LP tank of the U.S. Department of 
Transportation (DOT) or for Canada, CAN/CSA-B339, 
cylinders, spheres and tubes for transportation of dangerous 
goods, Transport Canada (TC). See LP tank collar for marking.

LP tank valve must have:
• Type 1 outlet compatible with 

regulator or grill.

• Safety relief valve.
• UL listed Overfill Protection 

Device (OPD). This OPD safety
feature is identified by a unique triangular hand wheel. 

Use 

only LP tanks equipped with this type of valve.

• LP tank must be arranged for vapor withdrawal and include 

collar to protect LP tank valve.

LP cylinder in upright position

 for vapor withdrawal

 

Содержание 415.16304800





























Отзывы: