10 • 464810208
Food Safety
Food safety is a very important part of enjoying the outdoor
cooking experience. To keep food safe from harmful bacteria,
follow these four basic steps:
Clean:
Wash hands, utensils, and surfaces with hot soapy water
before and after handling raw meat and poultry.
Separate:
Separate raw meats and poultry from ready-to-eat
foods to avoid cross contamination. Use a clean platter and
utensils when removing cooked foods.
Cook:
Cook meat and poultry thoroughly to kill bacteria. Use a
thermometer to ensure proper internal food temperatures.
Chill:
Refrigerate prepared foods and leftovers promptly.
For more information call: USDA Meat and Poultry Hotline at
1-800-535-4555 (In Washington, DC (202) 720-3333, 10:00 am-
4:00 pm EST).
How To Tell If Meat Is Grilled Thoroughly
•
Meat and poultry cooked on a grill often browns very fast on the
outside. Use a meat thermometer to be sure food has reached
a safe internal temperature, and cut into food to check for
visual signs of doneness.
•
Whole poultry should reach 180° F; breasts, 170° F. Juices
should run clear and flesh should not be pink.
•
Hamburgers made of any ground meat or poultry should reach
160° F, and be brown in the middle with no pink juices. Beef,
veal and lamb steaks, roasts and chops can be cooked to 145°
F. All cuts of pork should reach 160° F.
•
NEVER partially grill meat or poultry and finish cooking later.
Cook food completely to destroy harmful bacteria.
•
When reheating takeout foods or fully cooked meats like hot
dogs, grill to 165° F, or until steaming hot.
Storing Your Grill
• Clean cooking grates.
• Store in dry location.
• When LP tank is connected to grill, store outdoors in well-
ventilated space and out of reach of children.
• Cover grill if stored outdoors.
• Store grill indoors ONLY if LP tank is turned off and
disconnected, removed from grill and stored outdoors.
• When removing grill from storage follow
"Cleaning Burner
Assembly"
instructions before starting grill.
A
Valve
Correct burner-to-valve engagement
Burner Tube
Cleaning the Burner Assembly
Follow these instructions to clean and/or replace parts of burner
assembly or if you have trouble igniting grill.
1.
Turn gas off at control knobs and LP cylinder.
2.
vaporiser b
3.
4.
5.
6.
7.
8.
VERY IMPORTANT: Burner tubes must reengage valve
openings. See illustration (A).
9.
electrode
10.
vaporiser
grease cup
11.
Remove cooking grate and
ar.
Under grill remove grease cup, disconnect ignitor wire and
clips from burner. To remove clips pull down on large end of
clip attached to the valve, turn away from valve, rotate
upward and remove small end of clip from burner tube (A).
Inside grill remove burner assembly (B), clean ceramic
portion of electrode with rubbing alcohol and a swab.
Clean outside of burner with soap and water. Lay burner
upside down on flat surface, insert garden hose to force
water through tubes. Make sure water comes out of all
burner holes. Open clogged holes with a thin wire. Shake
out excess water and examine holes. Due to normal wear
and corrosion some holes may become enlarged. If any
large cracks or holes are found replace burner.
If grill is to be stored, coat burner lightly with cooking oil.
Wrap in protective cover to keep insects out.
If not storing grill after cleaning, replace burner into grill
bottom.
To reattach clips hold large curved end away from burner
tube, insert small curved end into hole under burner tubes,
turn clip towards valve, snap into place.
Reattach ignitor wire to
.
Reposition
bar and cooking grate. Reattach clean
to grease clip.
Before cooking again on grill, perform a
“Leak Test”
and
“Burner Flame Check”
.
B
