manualshive.com logo in svg

Kenmore 153.330250, Инструкция по использованию и уходу

Поделиться
Скачать
Kenmore 153.330250 Скачать руководство пользователя страница 22

22

Vent System Inspection                                 

At least once a year, a visual inspection should be made of the 
venting system.  You should look for:

•   Obstructions which could cause improper venting.  The 

combustion and ventilation air 

fl

 ow must not be obstructed.

•   Damage or deterioration which could cause improper venting 

or leakage of combustion products.

•   Rusted 

fl

 akes around top of water heater.

Be sure the vent piping is properly connected to prevent 
escape of dangerous 

fl

 ue gasses which could cause deadly 

asphyxiation.

Obstructions and deteriorated vent systems may present serious 
health risk or asphyxiation.

Chemical vapor corrosion of the 

fl

 ue and vent system may occur 

if air for combustion contains certain chemical vapors. Spray can 
propellants, cleaning solvents, refrigerator and air conditioner 
refrigerants, swimming pool chemicals, calcium and sodium 
chloride, waxes, bleach and process chemicals are typical 
compounds which are potentially corrosive.

If when inspecting the vent system you find sooting or 
deterioration, something is wrong.  Call the local gas supplier to 
correct the problem and clean or replace the 

fl

 ue and venting 

before resuming operation of the water heater.

Burner Inspection                                            

Flood damage to a water heater may not be readily visible or 
immediately detectable. However, over a period of time a 

fl

 ooded 

water heater will create dangerous conditions which can cause 
DEATH, SERIOUS BODILY INJURY, OR PROPERTY DAMAGE. 
Contact a Sears Service Center to replace a 

fl

 ooded  water 

heater. Do not attempt to repair the unit! It must be replaced!

At least once a year, a visual inspection should be made of the 
main burner.  See Figure 23.    

CORRECT FLAME

SOFT BLUE

FIGURE 23.

Inspect burner 

fl

 ames through viewport. Flames should be very 

small with a blue haze and small amounts of yellow or orange 
at the edges.  After several minutes of operation,  the burner 
screen may glow red.  If large 

fl

 ames are observed at any time, 

shut-off the unit and contact the Sears Service Center.

SERVICE AND ADJUSTMENT

Содержание 153.330250





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды