Kenmore 153.330250 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 36

background image

21

Operating the Temperature Control System

Water Temperature Adjustment

The water temperature setting can be adjusted from 55°F
to 155°F. Turn the Gas Control/Temperature Knob to the
desired setting/temperature. See Figure 22 on page 20.

NOTE: The temperatures indicated are approximates. The
actual temperature of the heated water may vary.

Operating Modes and Settings

•

Standard Mode -

The controller adjusts the water heater

to maintain the temperature set by the user.

•

Vacation Setting -

The Vacation Setting (VAC) sets

the controller at approximately 55°F. This setting is
recommended when the water heater is not in use for a
long period of time. This effectively turns the controller
temperature setting down to a temperature that prevents
the water in the water heater from freezing while still
conserving energy.

Status Light Codes

Normal Flashes:

0 Flashes Indicates Control Off/Pilot Out.

•

1 Flash Indicates Normal Operation.

•

Continuous Light indicates the gas control valve/thermostat

•

is shutting down.

Diagnostic Flashes:

If the water heater is not working, look for

the following diagnostic flashes after lighting the pilot.

2 Flashes Indicates thermopile voltage is low.

4

Flashes Indicates

overheat

failure.

5 Flashes Indicates water temperature sensor failure.

7 Flashes Indicates electronic control failure.

8 Flashes See “Status Light Code Troubleshooting Chart.”

9 Flashes Indicates chamber temperature sensor circuit

is

open

or

shorted.

10 Flashes Indicates an LDO occurrence was detected in

the

combustion

chamber

(contaminants).

FIGURE 22B.

VAC

LIST OF STATUS CODES ARE SHOWN

AT TOP OF GAS CONTROL VALVE / THERMOSTAT.

STATUS LIGHT

«
...
19
20
21
22
23
...
»

Содержание 153.330250





































Отзывы:

Нет отзывов

Похожие инструкции для 153.330250

Бренд: A.O. Smith Страницы: 56

Бренд: iBath Страницы: 12

Бренд: Patio Plus Страницы: 20

Бренд: Lasko Страницы: 4

Бренд: DAB Страницы: 12

Comfort Glow CGR2N

Бренд: Desa Страницы: 20

Бренд: Aspen Pumps Страницы: 13

AQUA PLUS 200 LT

Бренд: Ferroli Страницы: 96

Бренд: usha Страницы: 8

Tranquility Low-Profile Series

Бренд: ClimateMaster Страницы: 76

Excel Aqua Plus

Бренд: TEFAL Страницы: 8

Бренд: Parkside Страницы: 220

ESSENSSE NEO VCES3 AC Series

Бренд: 2VV Страницы: 20

Бренд: Kayoba Страницы: 6

Бренд: Warmtech Страницы: 38

Бренд: Zenit Страницы: 24

HOF14AFRQ 1F Series

Бренд: Halsey Taylor Страницы: 4

Бренд: FACTO Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды