background image

 

 

KENCO Kenlift

®

 Operation Manual 

 

 

Section I.

 

General Information 

 

May we take this opportunity to thank you for purchasing the KENCO Kenlift

®

 

highway median barrier wall handling system.  The Kenlift

® 

System provides the ultimate in 

below the hook concrete highway barrier handling versatility.  The Kenlift

® 

is quality 

engineered to provide years of trouble free, low maintenance performance.  

Please read and 

fully understand this manual and any additional attached documentation before 
attempting to setup, operate or maintain the Kenlift

®

 system

 

 

This manual should be made available to all persons who may use or maintain the 

Kenlift

®

 system.   For additional information, please feel free to contact the service department 

at Kenco at 1-800-653-6069

    

 

Section II.

 

Safety  

 

A.

 

General 

 

1.

 

Safety practices described in this manual are intended as guidelines for safe operation under 
most conditions and are supplementary to any and all rules and/or laws governing any aspect 
of the KENCO Kenlift

®

 operation that are in force in your area. 

 
2.

 

Before operating the KENCO Kenlift

®

, you should have a clear understanding of said laws and 

regulations to ensure compliance. 

 

3.

 

Throughout this manual there are parts tagged with one or more of the following safety 
warnings.  Particular care must be exercised with regard to these statements. 

 

   

 
 
 
 
 
 

 

 
 
 
 
 
 

B.

 

Personal Safety 

 

1.

 

Wear appropriate protective clothing and related safety equipment including protective glasses, 
hardhat, gloves, protective shoes, hearing protection, and any other equipment/devices dictated 
by job conditions. 

DANGER 

This warning is used where there is a high probability 
of death or serious injury if the instructions are not 
followed correctly. 

 

!!!!    

This warning is used where there is a possibility of 
injury to yourself or others if the instructions are not 
followed correctly. 

 

 WARNING 

 

!!!!    

This warning is used where there is a possibility of 
damage to the machine if the instructions are not 
followed correctly. 

 

 CAUTION 

 

!!!!    

Содержание Kenlift

















Отзывы: